-- Network Working Group H-K. Lam
-- Request for Comments: 3591 Lucent Technologies
-- Category: Standards Track M. Stewart
-- Dorado Software
-- A. Huynh
-- Cetus Networks
-- September 2003-- Definitions of Managed Objects for the Optical Interface TypeOPT-IF-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Gauge32,Integer32,Unsigned32, transmission
FROM SNMPv2-SMI
TEXTUAL-CONVENTION,RowPointer,RowStatus,TruthValueFROM SNMPv2-TC
SnmpAdminStringFROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
ifIndex
FROM IF-MIB;-- This is the MIB module for the OTN Interface objects.optIfMibModule MODULE-IDENTITYLAST-UPDATED"200308130000Z"ORGANIZATION"IETF AToM MIB Working Group"CONTACT-INFO"WG charter:
http://www.ietf.org/html.charters/atommib-charter.html
Mailing Lists:
General Discussion: atommib@research.telcordia.com
To Subscribe: atommib-request@research.telcordia.com
Editor: Hing-Kam Lam
Postal: Lucent Technologies, Room 4C-616
101 Crawfords Corner Road
Holmdel, NJ 07733
Tel: +1 732 949 8338
Email: hklam@lucent.com"DESCRIPTION"The MIB module to describe pre-OTN and OTN interfaces.
Copyright (C) The Internet Society (2003). This version
of this MIB module is part of RFC 3591; see the RFC
itself for full legal notices."REVISION"200308130000Z"DESCRIPTION"Initial version, published as RFC 3591."::={ transmission 133}-- textual conventionsOptIfAcTI::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The trace identifier (TI) accepted at the receiver."SYNTAXOCTETSTRING(SIZE(64))OptIfBitRateK::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Indicates the index 'k' that is used to
represent a supported bit rate and the different
versions of OPUk, ODUk and OTUk.
Allowed values of k are defined in ITU-T G.709.
Currently allowed values in G.709 are:
k=1 represents an approximate bit rate of 2.5 Gbit/s,
k=2 represents an approximate bit rate of 10 Gbit/s,
k=3 represents an approximate bit rate of 40 Gbit/s."SYNTAXInteger32OptIfDEGM::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if OptIfDEGM
consecutive bad PM Seconds are detected."SYNTAXUnsigned32(2..10)OptIfDEGThr::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to OptIfDEGThr."SYNTAXUnsigned32(1..100)OptIfDirectionality::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Indicates the directionality of an entity."
SYNTAXINTEGER{sink(1),source(2),bidirectional(3)}OptIfSinkOrSource::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Indicates the directionality of an entity
that is allowed only to be a source or sink."SYNTAXINTEGER{sink(1),source(2)}OptIfExDAPI::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The Destination Access Point Identifier (DAPI)
expected by the receiver."SYNTAXOCTETSTRING(SIZE(16))OptIfExSAPI::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The Source Access Point Identifier (SAPI)
expected by the receiver."SYNTAXOCTETSTRING(SIZE(16))OptIfIntervalNumber::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Uniquely identifies a 15-minute interval. The interval
identified by 1 is the most recently completed interval, and
the interval identified by n is the interval immediately
preceding the one identified by n-1."SYNTAXUnsigned32(1..96)OptIfTIMDetMode::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function."SYNTAXINTEGER{off(1),dapi(2),sapi(3),both(4)}OptIfTxTI::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The trace identifier (TI) transmitted."SYNTAXOCTETSTRING(SIZE(64))-- object groupsoptIfObjects OBJECTIDENTIFIER::={ optIfMibModule 1}optIfConfs OBJECTIDENTIFIER::={ optIfMibModule 2}optIfOTMn OBJECTIDENTIFIER::={ optIfObjects 1}optIfPerfMon OBJECTIDENTIFIER::={ optIfObjects 2}optIfOTSn OBJECTIDENTIFIER::={ optIfObjects 3}optIfOMSn OBJECTIDENTIFIER::={ optIfObjects 4}
optIfOChGroup OBJECTIDENTIFIER::={ optIfObjects 5}optIfOCh OBJECTIDENTIFIER::={ optIfObjects 6}optIfOTUk OBJECTIDENTIFIER::={ optIfObjects 7}optIfODUk OBJECTIDENTIFIER::={ optIfObjects 8}optIfODUkT OBJECTIDENTIFIER::={ optIfObjects 9}optIfGroups OBJECTIDENTIFIER::={ optIfConfs 1}optIfCompl OBJECTIDENTIFIER::={ optIfConfs 2}-- the optIfOTMn group
-- This group defines the OTM structure information of an
-- optical interface.-- OTMn TableoptIfOTMnTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTMnEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OTMn structure information."::={ optIfOTMn 1}optIfOTMnEntry OBJECT-TYPESYNTAX OptIfOTMnEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains the OTMn structure
information of an optical interface."INDEX{ ifIndex }::={ optIfOTMnTable 1}
OptIfOTMnEntry ::=SEQUENCE{
optIfOTMnOrder Unsigned32,
optIfOTMnReduced TruthValue,
optIfOTMnBitRates BITS,
optIfOTMnInterfaceType SnmpAdminString,
optIfOTMnTcmMax Unsigned32,
optIfOTMnOpticalReach INTEGER}optIfOTMnOrder OBJECT-TYPESYNTAXUnsigned32(1..900)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the order of the OTM, which
represents the maximum number of wavelengths that can be
supported at the bit rate(s) supported on the interface."::={ optIfOTMnEntry 1}optIfOTMnReduced OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates whether a reduced or full
functionality is supported at the interface. A value of
true means reduced. A value of false means full."::={ optIfOTMnEntry 2}optIfOTMnBitRates OBJECT-TYPESYNTAXBITS{ bitRateK1(0), bitRateK2(1), bitRateK3(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"This attribute is a bit map representing the bit
rate or set of bit rates supported on the interface.
The meaning of each bit position is as follows:
bitRateK1(0) is set if the 2.5 Gbit/s rate is supported
bitRateK2(1) is set if the 10 Gbit/s rate is supported
bitRateK3(2) is set if the 40 Gbit/s rate is supported
Note that each bit position corresponds to one possible
value of the type OptIfBitRateK.
The default value of this attribute is system specific."::={ optIfOTMnEntry 3}optIfOTMnInterfaceType OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object identifies the type of interface. The value of
this attribute will affect the behavior of the OTM with
respect to presence/absence of OTM Overhead Signal (OOS)
processing and TCM activation. For an IrDI interface,
there is no OOS processing and TCM activation is limited
to n levels as specified by a TCM level threshold.
This object contains two fields that are separated by
whitespace. The possible values are:
field 1: one of the 4-character ASCII strings
'IrDI' or 'IaDI'
field 2: free-form text consisting of printable
UTF-8 encoded characters
Note that field 2 is optional. If it is not present then there
is no requirement for trailing whitespace after field 1.
The default values are as follows:
field 1: 'IaDI'
field 2: an empty string."::={ optIfOTMnEntry 4}optIfOTMnTcmMax OBJECT-TYPESYNTAXUnsigned32(0..6)MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object identifies the maximum number of TCM
levels allowed for any Optical Channel contained
in this OTM. A new TCM activation will be rejected
if the requested level is greater than the threshold.
If InterfaceType object specifies a type of 'IaDI'
for this OTM, then this attribute is irrelevant.
Possible values: unsigned integers in the range
from 0 to 6 inclusive.
Default value: 3."::={ optIfOTMnEntry 5}optIfOTMnOpticalReach OBJECT-TYPESYNTAXINTEGER{ intraOffice(1), shortHaul(2), longHaul(3),veryLongHaul(4), ultraLongHaul(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the length the optical signal
may travel before requiring termination or regeneration.
The meaning of the enumeration are:
intraOffice(1) - intra-office (as defined in ITU-T G.957)
shortHaul(2) - short haul (as defined in ITU-T G.957)
longHaul(3) - long haul (as defined in ITU-T G.957)
veryLongHaul(4) - very long haul (as defined in ITU-T G.691)
ultraLongHaul(5)- ultra long haul (as defined in ITU-T G.691)"::={ optIfOTMnEntry 6}-- the optIfPerfMon group
-- This group defines performance monitoring objects for all
-- layers.-- PM interval tableoptIfPerfMonIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfPerfMonIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of 15-minute performance monitoring interval
information."::={ optIfPerfMon 1}optIfPerfMonIntervalEntry OBJECT-TYPESYNTAX OptIfPerfMonIntervalEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"A conceptual row that contains 15-minute performance
monitoring interval information of an interface."INDEX{ ifIndex }::={ optIfPerfMonIntervalTable 1}
OptIfPerfMonIntervalEntry ::=SEQUENCE{
optIfPerfMonCurrentTimeElapsed Gauge32,
optIfPerfMonCurDayTimeElapsed Gauge32,
optIfPerfMonIntervalNumIntervals Unsigned32,
optIfPerfMonIntervalNumInvalidIntervals Unsigned32}optIfPerfMonCurrentTimeElapsed OBJECT-TYPESYNTAXGauge32(0..900)UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of seconds elapsed in the current 15-minute
performance monitoring interval.
If, for some reason, such as an adjustment in the NE's
time-of-day clock, the number of seconds elapsed exceeds
the maximum value, then the maximum value will be returned."::={ optIfPerfMonIntervalEntry 1}optIfPerfMonCurDayTimeElapsed OBJECT-TYPESYNTAXGauge32(0..86400)UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of seconds elapsed in the current 24-hour interval
performance monitoring period.
If, for some reason, such as an adjustment in the NE's
time-of-day clock, the number of seconds elapsed exceeds
the maximum value, then the maximum value will be returned."::={ optIfPerfMonIntervalEntry 2}optIfPerfMonIntervalNumIntervals OBJECT-TYPESYNTAXUnsigned32(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of 15-minute intervals for which performance
monitoring data is available. The number is the same for all
the associated sub layers of the interface.
An optical interface must be capable of supporting at least
n intervals, where n is defined as follows:
The minimum value of n is 4.
The default of n is 32.
The maximum value of n is 96.
The value of this object will be n unless performance
monitoring was (re-)started for the interface within the last
(n*15) minutes, in which case the value will be the number of
complete 15-minute intervals since measurement was
(re-)started."::={ optIfPerfMonIntervalEntry 3}optIfPerfMonIntervalNumInvalidIntervals OBJECT-TYPESYNTAXUnsigned32(0..96)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of intervals in the range from 0 to
optIfPerfMonIntervalNumIntervals for which no performance
monitoring data is available and/or the data is invalid."::={ optIfPerfMonIntervalEntry 4}-- the optIfOTSn group
-- This group handles the configuration and performance
-- monitoring objects for OTS layers.-- OTSn config tableoptIfOTSnConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTSnConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OTSn configuration information."
::={ optIfOTSn 1}optIfOTSnConfigEntry OBJECT-TYPESYNTAX OptIfOTSnConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTSn configuration
information of an interface."INDEX{ ifIndex }::={ optIfOTSnConfigTable 1}
OptIfOTSnConfigEntry ::=SEQUENCE{
optIfOTSnDirectionality OptIfDirectionality,
optIfOTSnAprStatus SnmpAdminString,
optIfOTSnAprControl SnmpAdminString,
optIfOTSnTraceIdentifierTransmitted OptIfTxTI,
optIfOTSnDAPIExpected OptIfExDAPI,
optIfOTSnSAPIExpected OptIfExSAPI,
optIfOTSnTraceIdentifierAccepted OptIfAcTI,
optIfOTSnTIMDetMode OptIfTIMDetMode,
optIfOTSnTIMActEnabled TruthValue,
optIfOTSnCurrentStatus BITS}optIfOTSnDirectionality OBJECT-TYPESYNTAXOptIfDirectionalityMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the directionality of the entity."::={ optIfOTSnConfigEntry 1}optIfOTSnAprStatus OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This attribute indicates the status of the Automatic
Power Reduction (APR) function of the entity. Valid
values are 'on' and 'off'."::={ optIfOTSnConfigEntry 2}optIfOTSnAprControl OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object is a UTF-8 encoded string that specifies Automatic
Power Reduction (APR) control actions requested of this entity
(when written) and that returns the current APR control state
of this entity (when read). The values are implementation-defined.
Any implementation that instantiates this object must document the
set of values that it allows to be written, the set of values
that it will return, and what each of those values means."::={ optIfOTSnConfigEntry 3}optIfOTSnTraceIdentifierTransmitted OBJECT-TYPESYNTAXOptIfTxTIMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The trace identifier transmitted.
This object is applicable when optIfOTSnDirectionality has the
value source(2) or bidirectional(3).
This object does not apply to reduced-capability systems (i.e.,
those for which optIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1
has the value 'IrDI').
If no value is ever set by a management entity for the object
optIfOTSnTraceIdentifierTransmitted, system-specific default
value will be used. Any implementation that instantiates this
object must document the system-specific default value or how it
is derived."::={ optIfOTSnConfigEntry 4}optIfOTSnDAPIExpected OBJECT-TYPESYNTAXOptIfExDAPIMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The DAPI expected by the receiver.
This object is applicable when optIfOTSnDirectionality has the
value sink(1) or bidirectional(3). It has no effect if
optIfOTSnTIMDetMode has the value off(1) or sapi(3).
This object does not apply to reduced-capability systems (i.e.,
those for which optIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1
has the value 'IrDI')."::={ optIfOTSnConfigEntry 5}optIfOTSnSAPIExpected OBJECT-TYPESYNTAXOptIfExSAPIMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The SAPI expected by the receiver.
This object is applicable when optIfOTSnDirectionality has the
value sink(1) or bidirectional(3). It has no effect if
optIfOTSnTIMDetMode has the value off(1) or dapi(2).
This object does not apply to reduced-capability systems (i.e.,
those for which optIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1
has the value 'IrDI')."::={ optIfOTSnConfigEntry 6}optIfOTSnTraceIdentifierAccepted OBJECT-TYPESYNTAXOptIfAcTIMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The actual trace identifier received.
This object is applicable when optIfOTSnDirectionality has the
value sink(1) or bidirectional(3). Its value is unspecified
if optIfOTSnCurrentStatus has either or both of the
losO(5) and los(6) bits set.
This object does not apply to reduced-capability systems (i.e.,
those for which optIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1
has the value 'IrDI')."::={ optIfOTSnConfigEntry 7}optIfOTSnTIMDetMode OBJECT-TYPESYNTAXOptIfTIMDetModeMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function. This object is applicable
when optIfOTSnDirectionality has the value sink(1)
or bidirectional(3). The default value is off(1).
This object does not apply to reduced-capability systems (i.e.,
those for which optIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1
has the value 'IrDI').
The default value of this object is off(1)."::={ optIfOTSnConfigEntry 8}optIfOTSnTIMActEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled. This object
is applicable when optIfOTSnDirectionality has the
value sink(1) or bidirectional(3). It has no effect
when the value of optIfOTSnTIMDetMode is off(1).
This object does not apply to reduced-capability systems (i.e.,
those for which optIfOTMnReduced has the value true(1)) or
at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1
has the value 'IrDI').
The default value of this object is false(2)."::={ optIfOTSnConfigEntry 9}optIfOTSnCurrentStatus OBJECT-TYPESYNTAXBITS{bdiP(0),bdiO(1),bdi(2),tim(3),losP(4),losO(5),los(6)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"Indicates the defect condition of the entity, if any.
This object is applicable when optIfOTSnDirectionality
has the value sink(1) or bidirectional(3). In
reduced-capability systems or at IrDI interfaces
the only bit position that may be set is los(6)."::={ optIfOTSnConfigEntry 10}-- OTSn sink current table
-- Contains data for the current 15-minute performance monitoring
-- interval.optIfOTSnSinkCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTSnSinkCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OTSn sink performance monitoring information for
the current 15-minute interval."::={ optIfOTSn 2}optIfOTSnSinkCurrentEntry OBJECT-TYPESYNTAX OptIfOTSnSinkCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTSn sink performance
monitoring information of an interface for the current
15-minute interval."INDEX{ ifIndex }::={ optIfOTSnSinkCurrentTable 1}
OptIfOTSnSinkCurrentEntry ::=SEQUENCE{
optIfOTSnSinkCurrentSuspectedFlag TruthValue,
optIfOTSnSinkCurrentInputPower Integer32,
optIfOTSnSinkCurrentLowInputPower Integer32,
optIfOTSnSinkCurrentHighInputPower Integer32,
optIfOTSnSinkCurrentLowerInputPowerThreshold Integer32,
optIfOTSnSinkCurrentUpperInputPowerThreshold Integer32,
optIfOTSnSinkCurrentOutputPower Integer32,
optIfOTSnSinkCurrentLowOutputPower Integer32,
optIfOTSnSinkCurrentHighOutputPower Integer32,
optIfOTSnSinkCurrentLowerOutputPowerThreshold Integer32,
optIfOTSnSinkCurrentUpperOutputPowerThreshold Integer32}optIfOTSnSinkCurrentSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOTSnSinkCurrentEntry 1}optIfOTSnSinkCurrentInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the input."::={ optIfOTSnSinkCurrentEntry 2}optIfOTSnSinkCurrentLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
current 15-minute interval."::={ optIfOTSnSinkCurrentEntry 3}optIfOTSnSinkCurrentHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
current 15-minute interval."::={ optIfOTSnSinkCurrentEntry 4}
optIfOTSnSinkCurrentLowerInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on input power. If
optIfOTSnSinkCurrentInputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOTSnSinkCurrentEntry 5}optIfOTSnSinkCurrentUpperInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on input power. If
optIfOTSnSinkCurrentInputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOTSnSinkCurrentEntry 6}optIfOTSnSinkCurrentOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the output."::={ optIfOTSnSinkCurrentEntry 7}optIfOTSnSinkCurrentLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 15-minute interval."::={ optIfOTSnSinkCurrentEntry 8}optIfOTSnSinkCurrentHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 15-minute interval."::={ optIfOTSnSinkCurrentEntry 9}optIfOTSnSinkCurrentLowerOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on output power. If
optIfOTSnSinkCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOTSnSinkCurrentEntry 10}optIfOTSnSinkCurrentUpperOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on output power. If
optIfOTSnSinkCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOTSnSinkCurrentEntry 11}-- OTSn sink interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.optIfOTSnSinkIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTSnSinkIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of historical OTSn sink performance monitoring
information."::={ optIfOTSn 3}optIfOTSnSinkIntervalEntry OBJECT-TYPESYNTAX OptIfOTSnSinkIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTSn sink performance
monitoring information of an interface during a particular
historical interval."INDEX{ ifIndex, optIfOTSnSinkIntervalNumber }::={ optIfOTSnSinkIntervalTable 1}
OptIfOTSnSinkIntervalEntry ::=SEQUENCE{
optIfOTSnSinkIntervalNumber OptIfIntervalNumber,
optIfOTSnSinkIntervalSuspectedFlag TruthValue,
optIfOTSnSinkIntervalLastInputPower Integer32,
optIfOTSnSinkIntervalLowInputPower Integer32,
optIfOTSnSinkIntervalHighInputPower Integer32,
optIfOTSnSinkIntervalLastOutputPower Integer32,
optIfOTSnSinkIntervalLowOutputPower Integer32,
optIfOTSnSinkIntervalHighOutputPower Integer32}optIfOTSnSinkIntervalNumber OBJECT-TYPESYNTAXOptIfIntervalNumberMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies the interval."::={ optIfOTSnSinkIntervalEntry 1}optIfOTSnSinkIntervalSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOTSnSinkIntervalEntry 2}optIfOTSnSinkIntervalLastInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the input during the
interval."::={ optIfOTSnSinkIntervalEntry 3}optIfOTSnSinkIntervalLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
interval."::={ optIfOTSnSinkIntervalEntry 4}optIfOTSnSinkIntervalHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
interval."::={ optIfOTSnSinkIntervalEntry 5}optIfOTSnSinkIntervalLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output during the
interval."::={ optIfOTSnSinkIntervalEntry 6}optIfOTSnSinkIntervalLowOutputPower OBJECT-TYPE
SYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
interval."::={ optIfOTSnSinkIntervalEntry 7}optIfOTSnSinkIntervalHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
interval."::={ optIfOTSnSinkIntervalEntry 8}-- OTSn sink current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.optIfOTSnSinkCurDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTSnSinkCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OTSn sink performance monitoring information for
the current 24-hour interval."::={ optIfOTSn 4}optIfOTSnSinkCurDayEntry OBJECT-TYPESYNTAX OptIfOTSnSinkCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTSn sink performance
monitoring information of an interface for the current
24-hour interval."INDEX{ ifIndex }::={ optIfOTSnSinkCurDayTable 1}
OptIfOTSnSinkCurDayEntry ::=SEQUENCE{
optIfOTSnSinkCurDaySuspectedFlag TruthValue,
optIfOTSnSinkCurDayLowInputPower Integer32,
optIfOTSnSinkCurDayHighInputPower Integer32,
optIfOTSnSinkCurDayLowOutputPower Integer32,
optIfOTSnSinkCurDayHighOutputPower Integer32}optIfOTSnSinkCurDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOTSnSinkCurDayEntry 1}optIfOTSnSinkCurDayLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
current 24-hour interval."::={ optIfOTSnSinkCurDayEntry 2}optIfOTSnSinkCurDayHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
current 24-hour interval."::={ optIfOTSnSinkCurDayEntry 3}optIfOTSnSinkCurDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 24-hour interval."::={ optIfOTSnSinkCurDayEntry 4}optIfOTSnSinkCurDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 24-hour interval."::={ optIfOTSnSinkCurDayEntry 5}-- OTSn sink previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.optIfOTSnSinkPrevDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTSnSinkPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OTSn sink performance monitoring information for
the previous 24-hour interval."::={ optIfOTSn 5}optIfOTSnSinkPrevDayEntry OBJECT-TYPESYNTAX OptIfOTSnSinkPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTSn sink performance
monitoring information of an interface for the previous
24-hour interval."INDEX{ ifIndex }::={ optIfOTSnSinkPrevDayTable 1}
OptIfOTSnSinkPrevDayEntry ::=SEQUENCE{
optIfOTSnSinkPrevDaySuspectedFlag TruthValue,
optIfOTSnSinkPrevDayLastInputPower Integer32,
optIfOTSnSinkPrevDayLowInputPower Integer32,
optIfOTSnSinkPrevDayHighInputPower Integer32,
optIfOTSnSinkPrevDayLastOutputPower Integer32,
optIfOTSnSinkPrevDayLowOutputPower Integer32,
optIfOTSnSinkPrevDayHighOutputPower Integer32}optIfOTSnSinkPrevDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOTSnSinkPrevDayEntry 1}optIfOTSnSinkPrevDayLastInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the input during the
previous 24-hour interval."::={ optIfOTSnSinkPrevDayEntry 2}optIfOTSnSinkPrevDayLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
previous 24-hour interval."::={ optIfOTSnSinkPrevDayEntry 3}optIfOTSnSinkPrevDayHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
previous 24-hour interval."::={ optIfOTSnSinkPrevDayEntry 4}
optIfOTSnSinkPrevDayLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output during the
previous 24-hour interval."::={ optIfOTSnSinkPrevDayEntry 5}optIfOTSnSinkPrevDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOTSnSinkPrevDayEntry 6}optIfOTSnSinkPrevDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOTSnSinkPrevDayEntry 7}-- OTSn source current table
-- Contains data for the current 15-minute performance monitoring
-- interval.optIfOTSnSrcCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTSnSrcCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OTSn source performance monitoring information for
the current 15-minute interval."::={ optIfOTSn 6}optIfOTSnSrcCurrentEntry OBJECT-TYPESYNTAX OptIfOTSnSrcCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTSn source performance
monitoring information of an interface for the current
15-minute interval."INDEX{ ifIndex }::={ optIfOTSnSrcCurrentTable 1}
OptIfOTSnSrcCurrentEntry ::=SEQUENCE{
optIfOTSnSrcCurrentSuspectedFlag TruthValue,
optIfOTSnSrcCurrentOutputPower Integer32,
optIfOTSnSrcCurrentLowOutputPower Integer32,
optIfOTSnSrcCurrentHighOutputPower Integer32,
optIfOTSnSrcCurrentLowerOutputPowerThreshold Integer32,
optIfOTSnSrcCurrentUpperOutputPowerThreshold Integer32,
optIfOTSnSrcCurrentInputPower Integer32,
optIfOTSnSrcCurrentLowInputPower Integer32,
optIfOTSnSrcCurrentHighInputPower Integer32,
optIfOTSnSrcCurrentLowerInputPowerThreshold Integer32,
optIfOTSnSrcCurrentUpperInputPowerThreshold Integer32}optIfOTSnSrcCurrentSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOTSnSrcCurrentEntry 1}optIfOTSnSrcCurrentOutputPower OBJECT-TYPESYNTAXInteger32
UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the output."::={ optIfOTSnSrcCurrentEntry 2}optIfOTSnSrcCurrentLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 15-minute interval."::={ optIfOTSnSrcCurrentEntry 3}optIfOTSnSrcCurrentHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 15-minute interval."::={ optIfOTSnSrcCurrentEntry 4}optIfOTSnSrcCurrentLowerOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on output power. If
optIfOTSnSrcCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOTSnSrcCurrentEntry 5}optIfOTSnSrcCurrentUpperOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on output power. If
optIfOTSnSrcCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOTSnSrcCurrentEntry 6}optIfOTSnSrcCurrentInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the input."::={ optIfOTSnSrcCurrentEntry 7}optIfOTSnSrcCurrentLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
current 15-minute interval."::={ optIfOTSnSrcCurrentEntry 8}optIfOTSnSrcCurrentHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
current 15-minute interval."::={ optIfOTSnSrcCurrentEntry 9}optIfOTSnSrcCurrentLowerInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on input power. If
optIfOTSnSrcCurrentInputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOTSnSrcCurrentEntry 10}optIfOTSnSrcCurrentUpperInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on input power. If
optIfOTSnSrcCurrentInputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOTSnSrcCurrentEntry 11}-- OTSn source interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.optIfOTSnSrcIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTSnSrcIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of historical OTSn source performance monitoring
information."::={ optIfOTSn 7}optIfOTSnSrcIntervalEntry OBJECT-TYPESYNTAX OptIfOTSnSrcIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTSn source performance
monitoring information of an interface during a particular
historical interval."INDEX{ ifIndex, optIfOTSnSrcIntervalNumber }::={ optIfOTSnSrcIntervalTable 1}
OptIfOTSnSrcIntervalEntry ::=SEQUENCE{
optIfOTSnSrcIntervalNumber OptIfIntervalNumber,
optIfOTSnSrcIntervalSuspectedFlag TruthValue,
optIfOTSnSrcIntervalLastOutputPower Integer32,
optIfOTSnSrcIntervalLowOutputPower Integer32,
optIfOTSnSrcIntervalHighOutputPower Integer32,
optIfOTSnSrcIntervalLastInputPower Integer32,
optIfOTSnSrcIntervalLowInputPower Integer32,
optIfOTSnSrcIntervalHighInputPower Integer32}optIfOTSnSrcIntervalNumber OBJECT-TYPESYNTAXOptIfIntervalNumberMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies the interval."::={ optIfOTSnSrcIntervalEntry 1}optIfOTSnSrcIntervalSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOTSnSrcIntervalEntry 2}optIfOTSnSrcIntervalLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output during the
interval."::={ optIfOTSnSrcIntervalEntry 3}optIfOTSnSrcIntervalLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The lowest optical power monitored at the output during the
interval."::={ optIfOTSnSrcIntervalEntry 4}optIfOTSnSrcIntervalHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
interval."::={ optIfOTSnSrcIntervalEntry 5}optIfOTSnSrcIntervalLastInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the input during the
interval."::={ optIfOTSnSrcIntervalEntry 6}optIfOTSnSrcIntervalLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
interval."::={ optIfOTSnSrcIntervalEntry 7}optIfOTSnSrcIntervalHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
interval."::={ optIfOTSnSrcIntervalEntry 8}-- OTSn source current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.optIfOTSnSrcCurDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTSnSrcCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OTSn source performance monitoring information for
the current 24-hour interval."::={ optIfOTSn 8}optIfOTSnSrcCurDayEntry OBJECT-TYPESYNTAX OptIfOTSnSrcCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTSn source performance
monitoring information of an interface for the current
24-hour interval."INDEX{ ifIndex }::={ optIfOTSnSrcCurDayTable 1}
OptIfOTSnSrcCurDayEntry ::=SEQUENCE{
optIfOTSnSrcCurDaySuspectedFlag TruthValue,
optIfOTSnSrcCurDayLowOutputPower Integer32,
optIfOTSnSrcCurDayHighOutputPower Integer32,
optIfOTSnSrcCurDayLowInputPower Integer32,
optIfOTSnSrcCurDayHighInputPower Integer32}optIfOTSnSrcCurDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOTSnSrcCurDayEntry 1}optIfOTSnSrcCurDayLowOutputPower OBJECT-TYPESYNTAXInteger32
UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 24-hour interval."::={ optIfOTSnSrcCurDayEntry 2}optIfOTSnSrcCurDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 24-hour interval."::={ optIfOTSnSrcCurDayEntry 3}optIfOTSnSrcCurDayLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
current 24-hour interval."::={ optIfOTSnSrcCurDayEntry 4}optIfOTSnSrcCurDayHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
current 24-hour interval."::={ optIfOTSnSrcCurDayEntry 5}-- OTSn source previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.optIfOTSnSrcPrevDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTSnSrcPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OTSn source performance monitoring information for
the previous 24-hour interval."::={ optIfOTSn 9}optIfOTSnSrcPrevDayEntry OBJECT-TYPESYNTAX OptIfOTSnSrcPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTSn source performance
monitoring information of an interface for the previous
24-hour interval."INDEX{ ifIndex }::={ optIfOTSnSrcPrevDayTable 1}
OptIfOTSnSrcPrevDayEntry ::=SEQUENCE{
optIfOTSnSrcPrevDaySuspectedFlag TruthValue,
optIfOTSnSrcPrevDayLastOutputPower Integer32,
optIfOTSnSrcPrevDayLowOutputPower Integer32,
optIfOTSnSrcPrevDayHighOutputPower Integer32,
optIfOTSnSrcPrevDayLastInputPower Integer32,
optIfOTSnSrcPrevDayLowInputPower Integer32,
optIfOTSnSrcPrevDayHighInputPower Integer32}optIfOTSnSrcPrevDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOTSnSrcPrevDayEntry 1}optIfOTSnSrcPrevDayLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The last optical power monitored at the output during the
previous 24-hour interval."::={ optIfOTSnSrcPrevDayEntry 2}optIfOTSnSrcPrevDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOTSnSrcPrevDayEntry 3}optIfOTSnSrcPrevDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOTSnSrcPrevDayEntry 4}optIfOTSnSrcPrevDayLastInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the input during the
previous 24-hour interval."::={ optIfOTSnSrcPrevDayEntry 5}optIfOTSnSrcPrevDayLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
previous 24-hour interval."::={ optIfOTSnSrcPrevDayEntry 6}optIfOTSnSrcPrevDayHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
previous 24-hour interval."::={ optIfOTSnSrcPrevDayEntry 7}-- the optIfOMSn group
-- This group handles the configuration and performance monitoring
-- information for OMS layers.-- OMSn config tableoptIfOMSnConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOMSnConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OMSn configuration information."::={ optIfOMSn 1}optIfOMSnConfigEntry OBJECT-TYPESYNTAX OptIfOMSnConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OMSn configuration
information of an interface."INDEX{ ifIndex }::={ optIfOMSnConfigTable 1}
OptIfOMSnConfigEntry ::=SEQUENCE{
optIfOMSnDirectionality OptIfDirectionality,
optIfOMSnCurrentStatus BITS}optIfOMSnDirectionality OBJECT-TYPESYNTAXOptIfDirectionalityMAX-ACCESSread-only
STATUScurrentDESCRIPTION"Indicates the directionality of the entity."::={ optIfOMSnConfigEntry 1}optIfOMSnCurrentStatus OBJECT-TYPESYNTAXBITS{ssfP(0),ssfO(1),ssf(2),bdiP(3),bdiO(4),bdi(5),losP(6)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the defect condition of the entity, if any.
This object is applicable only to full capability
systems whose interface type is IaDI and for which
optIfOMSnDirectionality has the value sink(1) or
bidirectional(3)."::={ optIfOMSnConfigEntry 2}-- OMSn sink current table
-- Contains data for the current 15-minute performance monitoring
-- interval.optIfOMSnSinkCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOMSnSinkCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OMSn sink performance monitoring information for
the current 15-minute interval."::={ optIfOMSn 2}optIfOMSnSinkCurrentEntry OBJECT-TYPESYNTAX OptIfOMSnSinkCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OMSn sink performance
monitoring information of an interface for the current
15-minute interval."INDEX{ ifIndex }::={ optIfOMSnSinkCurrentTable 1}
OptIfOMSnSinkCurrentEntry ::=SEQUENCE{
optIfOMSnSinkCurrentSuspectedFlag TruthValue,
optIfOMSnSinkCurrentAggregatedInputPower Integer32,
optIfOMSnSinkCurrentLowAggregatedInputPower Integer32,
optIfOMSnSinkCurrentHighAggregatedInputPower Integer32,
optIfOMSnSinkCurrentLowerInputPowerThreshold Integer32,
optIfOMSnSinkCurrentUpperInputPowerThreshold Integer32,
optIfOMSnSinkCurrentOutputPower Integer32,
optIfOMSnSinkCurrentLowOutputPower Integer32,
optIfOMSnSinkCurrentHighOutputPower Integer32,
optIfOMSnSinkCurrentLowerOutputPowerThreshold Integer32,
optIfOMSnSinkCurrentUpperOutputPowerThreshold Integer32}optIfOMSnSinkCurrentSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOMSnSinkCurrentEntry 1}optIfOMSnSinkCurrentAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The aggregated optical power of all the DWDM input
channels."::={ optIfOMSnSinkCurrentEntry 2}optIfOMSnSinkCurrentLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power of all the DWDM input
channels during the current 15-minute interval."::={ optIfOMSnSinkCurrentEntry 3}optIfOMSnSinkCurrentHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power of all the DWDM input
channels during the current 15-minute interval."::={ optIfOMSnSinkCurrentEntry 4}optIfOMSnSinkCurrentLowerInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on aggregated input power. If
optIfOMSnSinkCurrentAggregatedInputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOMSnSinkCurrentEntry 5}optIfOMSnSinkCurrentUpperInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on aggregated input power. If
optIfOMSnSinkCurrentAggregatedInputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOMSnSinkCurrentEntry 6}optIfOMSnSinkCurrentOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the output."::={ optIfOMSnSinkCurrentEntry 7}optIfOMSnSinkCurrentLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output
during the current 15-minute interval."::={ optIfOMSnSinkCurrentEntry 8}optIfOMSnSinkCurrentHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output
during the current 15-minute interval."::={ optIfOMSnSinkCurrentEntry 9}optIfOMSnSinkCurrentLowerOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on output power. If
optIfOMSnSinkCurrentOutputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOMSnSinkCurrentEntry 10}optIfOMSnSinkCurrentUpperOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on output power. If
optIfOMSnSinkCurrentOutputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOMSnSinkCurrentEntry 11}-- OMSn sink interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.optIfOMSnSinkIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOMSnSinkIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of historical OMSn sink performance monitoring
information."::={ optIfOMSn 3}optIfOMSnSinkIntervalEntry OBJECT-TYPESYNTAX OptIfOMSnSinkIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OMSn sink performance
monitoring information of an interface during a particular
historical interval."INDEX{ ifIndex, optIfOMSnSinkIntervalNumber }::={ optIfOMSnSinkIntervalTable 1}
OptIfOMSnSinkIntervalEntry ::=SEQUENCE{
optIfOMSnSinkIntervalNumber OptIfIntervalNumber,
optIfOMSnSinkIntervalSuspectedFlag TruthValue,
optIfOMSnSinkIntervalLastAggregatedInputPower Integer32,
optIfOMSnSinkIntervalLowAggregatedInputPower Integer32,
optIfOMSnSinkIntervalHighAggregatedInputPower Integer32,
optIfOMSnSinkIntervalLastOutputPower Integer32,
optIfOMSnSinkIntervalLowOutputPower Integer32,
optIfOMSnSinkIntervalHighOutputPower Integer32}optIfOMSnSinkIntervalNumber OBJECT-TYPESYNTAXOptIfIntervalNumberMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies the interval."::={ optIfOMSnSinkIntervalEntry 1}optIfOMSnSinkIntervalSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOMSnSinkIntervalEntry 2}optIfOMSnSinkIntervalLastAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last aggregated optical power of all the DWDM input
channels during the interval."::={ optIfOMSnSinkIntervalEntry 3}optIfOMSnSinkIntervalLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The lowest aggregated optical power of all the DWDM input
channels during the interval."::={ optIfOMSnSinkIntervalEntry 4}optIfOMSnSinkIntervalHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power of all the DWDM input
channels during the interval."::={ optIfOMSnSinkIntervalEntry 5}optIfOMSnSinkIntervalLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power at the output
during the interval."::={ optIfOMSnSinkIntervalEntry 6}optIfOMSnSinkIntervalLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power at the output
during the interval."::={ optIfOMSnSinkIntervalEntry 7}optIfOMSnSinkIntervalHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power at the output
during the interval."::={ optIfOMSnSinkIntervalEntry 8}-- OMSn sink current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.optIfOMSnSinkCurDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOMSnSinkCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OMSn sink performance monitoring information for
the current 24-hour interval."::={ optIfOMSn 4}optIfOMSnSinkCurDayEntry OBJECT-TYPESYNTAX OptIfOMSnSinkCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OMSn sink performance
monitoring information of an interface for the current
24-hour interval."INDEX{ ifIndex }::={ optIfOMSnSinkCurDayTable 1}
OptIfOMSnSinkCurDayEntry ::=SEQUENCE{
optIfOMSnSinkCurDaySuspectedFlag TruthValue,
optIfOMSnSinkCurDayLowAggregatedInputPower Integer32,
optIfOMSnSinkCurDayHighAggregatedInputPower Integer32,
optIfOMSnSinkCurDayLowOutputPower Integer32,
optIfOMSnSinkCurDayHighOutputPower Integer32}optIfOMSnSinkCurDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOMSnSinkCurDayEntry 1}
optIfOMSnSinkCurDayLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power of all the DWDM input
channels during the current 24-hour interval."::={ optIfOMSnSinkCurDayEntry 2}optIfOMSnSinkCurDayHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power of all the DWDM input
channels during the current 24-hour interval."::={ optIfOMSnSinkCurDayEntry 3}optIfOMSnSinkCurDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power at the output
during the current 24-hour interval."::={ optIfOMSnSinkCurDayEntry 4}optIfOMSnSinkCurDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power at the output
during the current 24-hour interval."::={ optIfOMSnSinkCurDayEntry 5}-- OMSn sink previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.optIfOMSnSinkPrevDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOMSnSinkPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OMSn sink performance monitoring information for
the previous 24-hour interval."::={ optIfOMSn 5}optIfOMSnSinkPrevDayEntry OBJECT-TYPESYNTAX OptIfOMSnSinkPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OMSn sink performance
monitoring information of an interface for the previous
24-hour interval."INDEX{ ifIndex }::={ optIfOMSnSinkPrevDayTable 1}
OptIfOMSnSinkPrevDayEntry ::=SEQUENCE{
optIfOMSnSinkPrevDaySuspectedFlag TruthValue,
optIfOMSnSinkPrevDayLastAggregatedInputPower Integer32,
optIfOMSnSinkPrevDayLowAggregatedInputPower Integer32,
optIfOMSnSinkPrevDayHighAggregatedInputPower Integer32,
optIfOMSnSinkPrevDayLastOutputPower Integer32,
optIfOMSnSinkPrevDayLowOutputPower Integer32,
optIfOMSnSinkPrevDayHighOutputPower Integer32}optIfOMSnSinkPrevDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOMSnSinkPrevDayEntry 1}
optIfOMSnSinkPrevDayLastAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last aggregated optical power of all the DWDM input
channels during the previous 24-hour interval."::={ optIfOMSnSinkPrevDayEntry 2}optIfOMSnSinkPrevDayLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power of all the DWDM input
channels during the previous 24-hour interval."::={ optIfOMSnSinkPrevDayEntry 3}optIfOMSnSinkPrevDayHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power of all the DWDM input
channels during the previous 24-hour interval."::={ optIfOMSnSinkPrevDayEntry 4}optIfOMSnSinkPrevDayLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power at the output
during the previous 24-hour interval."::={ optIfOMSnSinkPrevDayEntry 5}optIfOMSnSinkPrevDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power at the output
during the previous 24-hour interval."::={ optIfOMSnSinkPrevDayEntry 6}optIfOMSnSinkPrevDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power at the output
during the previous 24-hour interval."::={ optIfOMSnSinkPrevDayEntry 7}-- OMSn source current table
-- Contains data for the current 15-minute performance monitoring
-- interval.optIfOMSnSrcCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOMSnSrcCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OMSn source performance monitoring information for
the current 15-minute interval."::={ optIfOMSn 6}optIfOMSnSrcCurrentEntry OBJECT-TYPESYNTAX OptIfOMSnSrcCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OMSn source performance
monitoring information of an interface for the current
15-minute interval."INDEX{ ifIndex }::={ optIfOMSnSrcCurrentTable 1}
OptIfOMSnSrcCurrentEntry ::=SEQUENCE{
optIfOMSnSrcCurrentSuspectedFlag TruthValue,
optIfOMSnSrcCurrentOutputPower Integer32,
optIfOMSnSrcCurrentLowOutputPower Integer32,
optIfOMSnSrcCurrentHighOutputPower Integer32,
optIfOMSnSrcCurrentLowerOutputPowerThreshold Integer32,
optIfOMSnSrcCurrentUpperOutputPowerThreshold Integer32,
optIfOMSnSrcCurrentAggregatedInputPower Integer32,
optIfOMSnSrcCurrentLowAggregatedInputPower Integer32,
optIfOMSnSrcCurrentHighAggregatedInputPower Integer32,
optIfOMSnSrcCurrentLowerInputPowerThreshold Integer32,
optIfOMSnSrcCurrentUpperInputPowerThreshold Integer32}optIfOMSnSrcCurrentSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOMSnSrcCurrentEntry 1}optIfOMSnSrcCurrentOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the output."::={ optIfOMSnSrcCurrentEntry 2}optIfOMSnSrcCurrentLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 15-minute interval."::={ optIfOMSnSrcCurrentEntry 3}optIfOMSnSrcCurrentHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 15-minute interval."::={ optIfOMSnSrcCurrentEntry 4}optIfOMSnSrcCurrentLowerOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on output power. If
optIfOMSnSrcCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOMSnSrcCurrentEntry 5}optIfOMSnSrcCurrentUpperOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on output power. If
optIfOMSnSrcCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOMSnSrcCurrentEntry 6}optIfOMSnSrcCurrentAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The aggregated optical power at the input."
::={ optIfOMSnSrcCurrentEntry 7}optIfOMSnSrcCurrentLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power at the input
during the current 15-minute interval."::={ optIfOMSnSrcCurrentEntry 8}optIfOMSnSrcCurrentHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power at the input
during the current 15-minute interval."::={ optIfOMSnSrcCurrentEntry 9}optIfOMSnSrcCurrentLowerInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on aggregated input power. If
optIfOMSnSrcCurrentAggregatedInputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOMSnSrcCurrentEntry 10}optIfOMSnSrcCurrentUpperInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on aggregated input power. If
optIfOMSnSrcCurrentAggregatedInputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOMSnSrcCurrentEntry 11}-- OMSn source interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.optIfOMSnSrcIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOMSnSrcIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of historical OMSn source performance monitoring
information."::={ optIfOMSn 7}optIfOMSnSrcIntervalEntry OBJECT-TYPESYNTAX OptIfOMSnSrcIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OMSn source performance
monitoring information of an interface during a particular
historical interval."INDEX{ ifIndex, optIfOMSnSrcIntervalNumber }::={ optIfOMSnSrcIntervalTable 1}
OptIfOMSnSrcIntervalEntry ::=SEQUENCE{
optIfOMSnSrcIntervalNumber OptIfIntervalNumber,
optIfOMSnSrcIntervalSuspectedFlag TruthValue,
optIfOMSnSrcIntervalLastOutputPower Integer32,
optIfOMSnSrcIntervalLowOutputPower Integer32,
optIfOMSnSrcIntervalHighOutputPower Integer32,
optIfOMSnSrcIntervalLastAggregatedInputPower Integer32,
optIfOMSnSrcIntervalLowAggregatedInputPower Integer32,
optIfOMSnSrcIntervalHighAggregatedInputPower Integer32}optIfOMSnSrcIntervalNumber OBJECT-TYPESYNTAXOptIfIntervalNumberMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies the interval."::={ optIfOMSnSrcIntervalEntry 1}optIfOMSnSrcIntervalSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOMSnSrcIntervalEntry 2}optIfOMSnSrcIntervalLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output during the
interval."::={ optIfOMSnSrcIntervalEntry 3}optIfOMSnSrcIntervalLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
interval."::={ optIfOMSnSrcIntervalEntry 4}optIfOMSnSrcIntervalHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
interval."::={ optIfOMSnSrcIntervalEntry 5}optIfOMSnSrcIntervalLastAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last aggregated optical power at the input
during the interval."::={ optIfOMSnSrcIntervalEntry 6}optIfOMSnSrcIntervalLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power at the input
during the interval."::={ optIfOMSnSrcIntervalEntry 7}optIfOMSnSrcIntervalHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power at the input
during the interval."::={ optIfOMSnSrcIntervalEntry 8}-- OMSn source current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.optIfOMSnSrcCurDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOMSnSrcCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OMSn source performance monitoring information for
the current 24-hour interval."
::={ optIfOMSn 8}optIfOMSnSrcCurDayEntry OBJECT-TYPESYNTAX OptIfOMSnSrcCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OMSn source performance
monitoring information of an interface for the current
24-hour interval."INDEX{ ifIndex }::={ optIfOMSnSrcCurDayTable 1}
OptIfOMSnSrcCurDayEntry ::=SEQUENCE{
optIfOMSnSrcCurDaySuspectedFlag TruthValue,
optIfOMSnSrcCurDayLowOutputPower Integer32,
optIfOMSnSrcCurDayHighOutputPower Integer32,
optIfOMSnSrcCurDayLowAggregatedInputPower Integer32,
optIfOMSnSrcCurDayHighAggregatedInputPower Integer32}optIfOMSnSrcCurDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOMSnSrcCurDayEntry 1}optIfOMSnSrcCurDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 24-hour interval."::={ optIfOMSnSrcCurDayEntry 2}optIfOMSnSrcCurDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 24-hour interval."::={ optIfOMSnSrcCurDayEntry 3}optIfOMSnSrcCurDayLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power at the input
during the current 24-hour interval."::={ optIfOMSnSrcCurDayEntry 4}optIfOMSnSrcCurDayHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power at the input
during the current 24-hour interval."::={ optIfOMSnSrcCurDayEntry 5}-- OMSn source previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.optIfOMSnSrcPrevDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOMSnSrcPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OMSn source performance monitoring information for
the previous 24-hour interval."::={ optIfOMSn 9}optIfOMSnSrcPrevDayEntry OBJECT-TYPESYNTAX OptIfOMSnSrcPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OMSn source performance
monitoring information of an interface for the previous
24-hour interval."INDEX{ ifIndex }::={ optIfOMSnSrcPrevDayTable 1}
OptIfOMSnSrcPrevDayEntry ::=SEQUENCE{
optIfOMSnSrcPrevDaySuspectedFlag TruthValue,
optIfOMSnSrcPrevDayLastOutputPower Integer32,
optIfOMSnSrcPrevDayLowOutputPower Integer32,
optIfOMSnSrcPrevDayHighOutputPower Integer32,
optIfOMSnSrcPrevDayLastAggregatedInputPower Integer32,
optIfOMSnSrcPrevDayLowAggregatedInputPower Integer32,
optIfOMSnSrcPrevDayHighAggregatedInputPower Integer32}optIfOMSnSrcPrevDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOMSnSrcPrevDayEntry 1}optIfOMSnSrcPrevDayLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output during the
previous 24-hour interval."::={ optIfOMSnSrcPrevDayEntry 2}optIfOMSnSrcPrevDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOMSnSrcPrevDayEntry 3}optIfOMSnSrcPrevDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOMSnSrcPrevDayEntry 4}optIfOMSnSrcPrevDayLastAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last aggregated optical power at the input during the
previous 24-hour interval."::={ optIfOMSnSrcPrevDayEntry 5}optIfOMSnSrcPrevDayLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power at the input during the
previous 24-hour interval."::={ optIfOMSnSrcPrevDayEntry 6}optIfOMSnSrcPrevDayHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The highest aggregated optical power at the input during the
previous 24-hour interval."::={ optIfOMSnSrcPrevDayEntry 7}-- the optIfOChGroup group
-- This group handles the configuration and performance monitoring
-- information for OChGroup layers.-- OChGroup config tableoptIfOChGroupConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChGroupConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OChGroup configuration information."::={ optIfOChGroup 1}optIfOChGroupConfigEntry OBJECT-TYPESYNTAX OptIfOChGroupConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OChGroup configuration
information of an interface."INDEX{ ifIndex }::={ optIfOChGroupConfigTable 1}
OptIfOChGroupConfigEntry ::=SEQUENCE{
optIfOChGroupDirectionality OptIfDirectionality}optIfOChGroupDirectionality OBJECT-TYPESYNTAXOptIfDirectionalityMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the directionality of the entity."::={ optIfOChGroupConfigEntry 1}-- OChGroup sink current table
-- Contains data for the current 15-minute performance monitoring
-- interval.optIfOChGroupSinkCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChGroupSinkCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OChGroup sink performance monitoring information for
the current 15-minute interval."::={ optIfOChGroup 2}optIfOChGroupSinkCurrentEntry OBJECT-TYPESYNTAX OptIfOChGroupSinkCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OChGroup sink performance
monitoring information of an interface for the current
15-minute interval."INDEX{ ifIndex }::={ optIfOChGroupSinkCurrentTable 1}
OptIfOChGroupSinkCurrentEntry ::=SEQUENCE{
optIfOChGroupSinkCurrentSuspectedFlag TruthValue,
optIfOChGroupSinkCurrentAggregatedInputPower Integer32,
optIfOChGroupSinkCurrentLowAggregatedInputPower Integer32,
optIfOChGroupSinkCurrentHighAggregatedInputPower Integer32,
optIfOChGroupSinkCurrentLowerInputPowerThreshold Integer32,
optIfOChGroupSinkCurrentUpperInputPowerThreshold Integer32,
optIfOChGroupSinkCurrentOutputPower Integer32,
optIfOChGroupSinkCurrentLowOutputPower Integer32,
optIfOChGroupSinkCurrentHighOutputPower Integer32,
optIfOChGroupSinkCurrentLowerOutputPowerThreshold Integer32,
optIfOChGroupSinkCurrentUpperOutputPowerThreshold Integer32}optIfOChGroupSinkCurrentSuspectedFlag OBJECT-TYPE
SYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChGroupSinkCurrentEntry 1}optIfOChGroupSinkCurrentAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The aggregated optical power of all the DWDM input
channels in the OChGroup."::={ optIfOChGroupSinkCurrentEntry 2}optIfOChGroupSinkCurrentLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power of all the DWDM input
channels in the OChGroup during the current 15-minute interval."::={ optIfOChGroupSinkCurrentEntry 3}optIfOChGroupSinkCurrentHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power of all the DWDM input
channels in the OChGroup during the current 15-minute interval."::={ optIfOChGroupSinkCurrentEntry 4}optIfOChGroupSinkCurrentLowerInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on aggregated input power. If
optIfOChGroupSinkCurrentAggregatedInputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChGroupSinkCurrentEntry 5}optIfOChGroupSinkCurrentUpperInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on aggregated input power. If
optIfOChGroupSinkCurrentAggregatedInputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChGroupSinkCurrentEntry 6}optIfOChGroupSinkCurrentOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the output
in the OChGroup."::={ optIfOChGroupSinkCurrentEntry 7}optIfOChGroupSinkCurrentLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output
in the OChGroup during the current 15-minute interval."::={ optIfOChGroupSinkCurrentEntry 8}optIfOChGroupSinkCurrentHighOutputPower OBJECT-TYPESYNTAXInteger32
UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output
in the OChGroup during the current 15-minute interval."::={ optIfOChGroupSinkCurrentEntry 9}optIfOChGroupSinkCurrentLowerOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on the output power. If
optIfOChGroupSinkCurrentOutputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChGroupSinkCurrentEntry 10}optIfOChGroupSinkCurrentUpperOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on the output power. If
optIfOChGroupSinkCurrentOutputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChGroupSinkCurrentEntry 11}-- OChGroup sink interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.optIfOChGroupSinkIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChGroupSinkIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of historical OChGroup sink performance monitoring
information."::={ optIfOChGroup 3}optIfOChGroupSinkIntervalEntry OBJECT-TYPESYNTAX OptIfOChGroupSinkIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OChGroup sink performance
monitoring information of an interface during a particular
historical interval."INDEX{ ifIndex, optIfOChGroupSinkIntervalNumber }::={ optIfOChGroupSinkIntervalTable 1}
OptIfOChGroupSinkIntervalEntry ::=SEQUENCE{
optIfOChGroupSinkIntervalNumber OptIfIntervalNumber,
optIfOChGroupSinkIntervalSuspectedFlag TruthValue,
optIfOChGroupSinkIntervalLastAggregatedInputPower Integer32,
optIfOChGroupSinkIntervalLowAggregatedInputPower Integer32,
optIfOChGroupSinkIntervalHighAggregatedInputPower Integer32,
optIfOChGroupSinkIntervalLastOutputPower Integer32,
optIfOChGroupSinkIntervalLowOutputPower Integer32,
optIfOChGroupSinkIntervalHighOutputPower Integer32}optIfOChGroupSinkIntervalNumber OBJECT-TYPESYNTAXOptIfIntervalNumberMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies the interval."::={ optIfOChGroupSinkIntervalEntry 1}optIfOChGroupSinkIntervalSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."
::={ optIfOChGroupSinkIntervalEntry 2}optIfOChGroupSinkIntervalLastAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last aggregated optical power of all the DWDM input
channels in the OChGroup during the interval."::={ optIfOChGroupSinkIntervalEntry 3}optIfOChGroupSinkIntervalLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power of all the DWDM input
channels in the OChGroup during the interval."::={ optIfOChGroupSinkIntervalEntry 4}optIfOChGroupSinkIntervalHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power of all the DWDM input
channels in the OChGroup during the interval."::={ optIfOChGroupSinkIntervalEntry 5}optIfOChGroupSinkIntervalLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output
in the OChGroup during the interval."::={ optIfOChGroupSinkIntervalEntry 6}optIfOChGroupSinkIntervalLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output
in the OChGroup during the interval."::={ optIfOChGroupSinkIntervalEntry 7}optIfOChGroupSinkIntervalHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output
in the OChGroup during the interval."::={ optIfOChGroupSinkIntervalEntry 8}-- OChGroup sink current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.optIfOChGroupSinkCurDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChGroupSinkCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OChGroup sink performance monitoring information for
the current 24-hour interval."::={ optIfOChGroup 4}optIfOChGroupSinkCurDayEntry OBJECT-TYPESYNTAX OptIfOChGroupSinkCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OChGroup sink performance
monitoring information of an interface for the current
24-hour interval."INDEX{ ifIndex }
::={ optIfOChGroupSinkCurDayTable 1}
OptIfOChGroupSinkCurDayEntry ::=SEQUENCE{
optIfOChGroupSinkCurDaySuspectedFlag TruthValue,
optIfOChGroupSinkCurDayLowAggregatedInputPower Integer32,
optIfOChGroupSinkCurDayHighAggregatedInputPower Integer32,
optIfOChGroupSinkCurDayLowOutputPower Integer32,
optIfOChGroupSinkCurDayHighOutputPower Integer32}optIfOChGroupSinkCurDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChGroupSinkCurDayEntry 1}optIfOChGroupSinkCurDayLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power of all the DWDM input
channels in the OChGroup during the current 24-hour interval."::={ optIfOChGroupSinkCurDayEntry 2}optIfOChGroupSinkCurDayHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power of all the DWDM input
channels in the OChGroup during the current 24-hour interval."::={ optIfOChGroupSinkCurDayEntry 3}optIfOChGroupSinkCurDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output
in the OChGroup during the current 24-hour interval."::={ optIfOChGroupSinkCurDayEntry 4}optIfOChGroupSinkCurDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output
in the OChGroup during the current 24-hour interval."::={ optIfOChGroupSinkCurDayEntry 5}-- OChGroup sink previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.optIfOChGroupSinkPrevDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChGroupSinkPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OChGroup sink performance monitoring information for
the previous 24-hour interval."::={ optIfOChGroup 5}optIfOChGroupSinkPrevDayEntry OBJECT-TYPESYNTAX OptIfOChGroupSinkPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OChGroup sink performance
monitoring information of an interface for the previous
24-hour interval."INDEX{ ifIndex }::={ optIfOChGroupSinkPrevDayTable 1}
OptIfOChGroupSinkPrevDayEntry ::=SEQUENCE{
optIfOChGroupSinkPrevDaySuspectedFlag TruthValue,
optIfOChGroupSinkPrevDayLastAggregatedInputPower Integer32,
optIfOChGroupSinkPrevDayLowAggregatedInputPower Integer32,
optIfOChGroupSinkPrevDayHighAggregatedInputPower Integer32,
optIfOChGroupSinkPrevDayLastOutputPower Integer32,
optIfOChGroupSinkPrevDayLowOutputPower Integer32,
optIfOChGroupSinkPrevDayHighOutputPower Integer32}optIfOChGroupSinkPrevDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChGroupSinkPrevDayEntry 1}optIfOChGroupSinkPrevDayLastAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last aggregated optical power of all the DWDM input
channels in the OChGroup during the previous 24-hour interval."::={ optIfOChGroupSinkPrevDayEntry 2}optIfOChGroupSinkPrevDayLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power of all the DWDM input
channels in the OChGroup during the previous 24-hour interval."::={ optIfOChGroupSinkPrevDayEntry 3}optIfOChGroupSinkPrevDayHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power of all the DWDM input
channels in the OChGroup during the previous 24-hour interval."::={ optIfOChGroupSinkPrevDayEntry 4}optIfOChGroupSinkPrevDayLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output
in the OChGroup during the previous 24-hour interval."::={ optIfOChGroupSinkPrevDayEntry 5}optIfOChGroupSinkPrevDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output
in the OChGroup during the previous 24-hour interval."::={ optIfOChGroupSinkPrevDayEntry 6}optIfOChGroupSinkPrevDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output
in the OChGroup during the previous 24-hour interval."
::={ optIfOChGroupSinkPrevDayEntry 7}-- OChGroup source current table
-- Contains data for the current 15-minute performance monitoring
-- interval.optIfOChGroupSrcCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChGroupSrcCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OChGroup source performance monitoring information for
the current 15-minute interval."::={ optIfOChGroup 6}optIfOChGroupSrcCurrentEntry OBJECT-TYPESYNTAX OptIfOChGroupSrcCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OChGroup source performance
monitoring information of an interface for the current
15-minute interval."INDEX{ ifIndex }::={ optIfOChGroupSrcCurrentTable 1}
OptIfOChGroupSrcCurrentEntry ::=SEQUENCE{
optIfOChGroupSrcCurrentSuspectedFlag TruthValue,
optIfOChGroupSrcCurrentOutputPower Integer32,
optIfOChGroupSrcCurrentLowOutputPower Integer32,
optIfOChGroupSrcCurrentHighOutputPower Integer32,
optIfOChGroupSrcCurrentLowerOutputPowerThreshold Integer32,
optIfOChGroupSrcCurrentUpperOutputPowerThreshold Integer32,
optIfOChGroupSrcCurrentAggregatedInputPower Integer32,
optIfOChGroupSrcCurrentLowAggregatedInputPower Integer32,
optIfOChGroupSrcCurrentHighAggregatedInputPower Integer32,
optIfOChGroupSrcCurrentLowerInputPowerThreshold Integer32,
optIfOChGroupSrcCurrentUpperInputPowerThreshold Integer32}optIfOChGroupSrcCurrentSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChGroupSrcCurrentEntry 1}optIfOChGroupSrcCurrentOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the output."::={ optIfOChGroupSrcCurrentEntry 2}optIfOChGroupSrcCurrentLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 15-minute interval."::={ optIfOChGroupSrcCurrentEntry 3}optIfOChGroupSrcCurrentHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 15-minute interval."::={ optIfOChGroupSrcCurrentEntry 4}optIfOChGroupSrcCurrentLowerOutputPowerThreshold OBJECT-TYPE
SYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on output power. If
optIfOChGroupSrcCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChGroupSrcCurrentEntry 5}optIfOChGroupSrcCurrentUpperOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on output power. If
optIfOChGroupSrcCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChGroupSrcCurrentEntry 6}optIfOChGroupSrcCurrentAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The aggregated optical power monitored at the input."::={ optIfOChGroupSrcCurrentEntry 7}optIfOChGroupSrcCurrentLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power monitored at the input
during the current 15-minute interval."::={ optIfOChGroupSrcCurrentEntry 8}optIfOChGroupSrcCurrentHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power monitored at the input
during the current 15-minute interval."::={ optIfOChGroupSrcCurrentEntry 9}optIfOChGroupSrcCurrentLowerInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on input power. If
optIfOChGroupSrcCurrentAggregatedInputPower drops to this value
or below, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChGroupSrcCurrentEntry 10}optIfOChGroupSrcCurrentUpperInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on input power. If
optIfOChGroupSrcCurrentAggregatedInputPower reaches or exceeds
this value, a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChGroupSrcCurrentEntry 11}-- OChGroup source interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.optIfOChGroupSrcIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChGroupSrcIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of historical OChGroup source performance monitoring
information."::={ optIfOChGroup 7}optIfOChGroupSrcIntervalEntry OBJECT-TYPESYNTAX OptIfOChGroupSrcIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OChGroup source performance
monitoring information of an interface during a particular
historical interval."INDEX{ ifIndex, optIfOChGroupSrcIntervalNumber }::={ optIfOChGroupSrcIntervalTable 1}
OptIfOChGroupSrcIntervalEntry ::=SEQUENCE{
optIfOChGroupSrcIntervalNumber OptIfIntervalNumber,
optIfOChGroupSrcIntervalSuspectedFlag TruthValue,
optIfOChGroupSrcIntervalLastOutputPower Integer32,
optIfOChGroupSrcIntervalLowOutputPower Integer32,
optIfOChGroupSrcIntervalHighOutputPower Integer32,
optIfOChGroupSrcIntervalLastAggregatedInputPower Integer32,
optIfOChGroupSrcIntervalLowAggregatedInputPower Integer32,
optIfOChGroupSrcIntervalHighAggregatedInputPower Integer32}optIfOChGroupSrcIntervalNumber OBJECT-TYPESYNTAXOptIfIntervalNumberMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies the interval."::={ optIfOChGroupSrcIntervalEntry 1}optIfOChGroupSrcIntervalSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChGroupSrcIntervalEntry 2}optIfOChGroupSrcIntervalLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output during the
interval."::={ optIfOChGroupSrcIntervalEntry 3}optIfOChGroupSrcIntervalLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
interval."::={ optIfOChGroupSrcIntervalEntry 4}optIfOChGroupSrcIntervalHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
interval."::={ optIfOChGroupSrcIntervalEntry 5}optIfOChGroupSrcIntervalLastAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last aggregated optical power monitored at the input
during the interval."::={ optIfOChGroupSrcIntervalEntry 6}optIfOChGroupSrcIntervalLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power monitored at the input
during the interval."::={ optIfOChGroupSrcIntervalEntry 7}optIfOChGroupSrcIntervalHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power monitored at the input
during the interval."::={ optIfOChGroupSrcIntervalEntry 8}-- OChGroup source current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.optIfOChGroupSrcCurDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChGroupSrcCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OChGroup source performance monitoring information for
the current 24-hour interval."::={ optIfOChGroup 8}optIfOChGroupSrcCurDayEntry OBJECT-TYPESYNTAX OptIfOChGroupSrcCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OChGroup source performance
monitoring information of an interface for the current
24-hour interval."INDEX{ ifIndex }::={ optIfOChGroupSrcCurDayTable 1}
OptIfOChGroupSrcCurDayEntry ::=SEQUENCE{
optIfOChGroupSrcCurDaySuspectedFlag TruthValue,
optIfOChGroupSrcCurDayLowOutputPower Integer32,
optIfOChGroupSrcCurDayHighOutputPower Integer32,
optIfOChGroupSrcCurDayLowAggregatedInputPower Integer32,
optIfOChGroupSrcCurDayHighAggregatedInputPower Integer32}optIfOChGroupSrcCurDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChGroupSrcCurDayEntry 1}optIfOChGroupSrcCurDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 24-hour interval."::={ optIfOChGroupSrcCurDayEntry 2}optIfOChGroupSrcCurDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 24-hour interval."::={ optIfOChGroupSrcCurDayEntry 3}optIfOChGroupSrcCurDayLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power monitored at the input
during the current 24-hour interval."::={ optIfOChGroupSrcCurDayEntry 4}optIfOChGroupSrcCurDayHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power monitored at the input
during the current 24-hour interval."::={ optIfOChGroupSrcCurDayEntry 5}-- OChGroup source previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.optIfOChGroupSrcPrevDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChGroupSrcPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OChGroup source performance monitoring information for
the previous 24-hour interval."::={ optIfOChGroup 9}optIfOChGroupSrcPrevDayEntry OBJECT-TYPESYNTAX OptIfOChGroupSrcPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OChGroup source performance
monitoring information of an interface for the previous
24-hour interval."INDEX{ ifIndex }::={ optIfOChGroupSrcPrevDayTable 1}
OptIfOChGroupSrcPrevDayEntry ::=SEQUENCE{
optIfOChGroupSrcPrevDaySuspectedFlag TruthValue,
optIfOChGroupSrcPrevDayLastOutputPower Integer32,
optIfOChGroupSrcPrevDayLowOutputPower Integer32,
optIfOChGroupSrcPrevDayHighOutputPower Integer32,
optIfOChGroupSrcPrevDayLastAggregatedInputPower Integer32,
optIfOChGroupSrcPrevDayLowAggregatedInputPower Integer32,
optIfOChGroupSrcPrevDayHighAggregatedInputPower Integer32}optIfOChGroupSrcPrevDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChGroupSrcPrevDayEntry 1}optIfOChGroupSrcPrevDayLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output during the
previous 24-hour interval."::={ optIfOChGroupSrcPrevDayEntry 2}optIfOChGroupSrcPrevDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOChGroupSrcPrevDayEntry 3}
optIfOChGroupSrcPrevDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOChGroupSrcPrevDayEntry 4}optIfOChGroupSrcPrevDayLastAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last aggregated optical power monitored at the input
during the previous 24-hour interval."::={ optIfOChGroupSrcPrevDayEntry 5}optIfOChGroupSrcPrevDayLowAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest aggregated optical power monitored at the input
during the previous 24-hour interval."::={ optIfOChGroupSrcPrevDayEntry 6}optIfOChGroupSrcPrevDayHighAggregatedInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest aggregated optical power monitored at the input
during the previous 24-hour interval."::={ optIfOChGroupSrcPrevDayEntry 7}-- the optIfOCh group-- This group handles the configuration and
-- performance monitoring information for OCh layers.-- OCh config tableoptIfOChConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OCh configuration information."::={ optIfOCh 1}optIfOChConfigEntry OBJECT-TYPESYNTAX OptIfOChConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OCh configuration
information of an interface."INDEX{ ifIndex }::={ optIfOChConfigTable 1}
OptIfOChConfigEntry ::=SEQUENCE{
optIfOChDirectionality OptIfDirectionality,
optIfOChCurrentStatus BITS}optIfOChDirectionality OBJECT-TYPESYNTAXOptIfDirectionalityMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the directionality of the entity."::={ optIfOChConfigEntry 1}optIfOChCurrentStatus OBJECT-TYPESYNTAXBITS{losP(0),los(1),oci(2),ssfP(3),
ssfO(4),ssf(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the defect condition of the entity, if any.
This object is applicable when optIfOChDirectionality
has the value sink(1) or bidirectional(3).
In full-capability systems the bit position los(1) is not used.
In reduced-capability systems or at IrDI interfaces only
the bit positions los(1) and ssfP(3) are used."::={ optIfOChConfigEntry 2}-- OCh sink current table
-- Contains data for the current 15-minute performance monitoring
-- interval.optIfOChSinkCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChSinkCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OCh sink performance monitoring information for
the current 15-minute interval."::={ optIfOCh 2}optIfOChSinkCurrentEntry OBJECT-TYPESYNTAX OptIfOChSinkCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OCh sink performance
monitoring information for an interface for the current
15-minute interval."INDEX{ ifIndex }::={ optIfOChSinkCurrentTable 1}
OptIfOChSinkCurrentEntry ::=SEQUENCE{
optIfOChSinkCurrentSuspectedFlag TruthValue,
optIfOChSinkCurrentInputPower Integer32,
optIfOChSinkCurrentLowInputPower Integer32,
optIfOChSinkCurrentHighInputPower Integer32,
optIfOChSinkCurrentLowerInputPowerThreshold Integer32,
optIfOChSinkCurrentUpperInputPowerThreshold Integer32}optIfOChSinkCurrentSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChSinkCurrentEntry 1}optIfOChSinkCurrentInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the input."::={ optIfOChSinkCurrentEntry 2}optIfOChSinkCurrentLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
current 15-minute interval."::={ optIfOChSinkCurrentEntry 3}optIfOChSinkCurrentHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
current 15-minute interval."::={ optIfOChSinkCurrentEntry 4}
optIfOChSinkCurrentLowerInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on input power. If
optIfOChSinkCurrentInputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChSinkCurrentEntry 5}optIfOChSinkCurrentUpperInputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on input power. If
optIfOChSinkCurrentInputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChSinkCurrentEntry 6}-- OCh sink interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.optIfOChSinkIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChSinkIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of historical OCh sink performance monitoring
information."::={ optIfOCh 3}optIfOChSinkIntervalEntry OBJECT-TYPESYNTAX OptIfOChSinkIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OCh sink performance
monitoring information of an interface during a particular
historical interval."INDEX{ ifIndex, optIfOChSinkIntervalNumber }::={ optIfOChSinkIntervalTable 1}
OptIfOChSinkIntervalEntry ::=SEQUENCE{
optIfOChSinkIntervalNumber OptIfIntervalNumber,
optIfOChSinkIntervalSuspectedFlag TruthValue,
optIfOChSinkIntervalLastInputPower Integer32,
optIfOChSinkIntervalLowInputPower Integer32,
optIfOChSinkIntervalHighInputPower Integer32}optIfOChSinkIntervalNumber OBJECT-TYPESYNTAXOptIfIntervalNumberMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies the interval."::={ optIfOChSinkIntervalEntry 1}optIfOChSinkIntervalSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChSinkIntervalEntry 2}optIfOChSinkIntervalLastInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the input during the
interval."::={ optIfOChSinkIntervalEntry 3}optIfOChSinkIntervalLowInputPower OBJECT-TYPESYNTAXInteger32
UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
interval."::={ optIfOChSinkIntervalEntry 4}optIfOChSinkIntervalHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
interval."::={ optIfOChSinkIntervalEntry 5}-- OCh sink current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.optIfOChSinkCurDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChSinkCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OCh sink performance monitoring information for
the current 24-hour interval."::={ optIfOCh 4}optIfOChSinkCurDayEntry OBJECT-TYPESYNTAX OptIfOChSinkCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OCh sink performance
monitoring information of an interface for the current
24-hour interval."INDEX{ ifIndex }::={ optIfOChSinkCurDayTable 1}
OptIfOChSinkCurDayEntry ::=SEQUENCE{
optIfOChSinkCurDaySuspectedFlag TruthValue,
optIfOChSinkCurDayLowInputPower Integer32,
optIfOChSinkCurDayHighInputPower Integer32}optIfOChSinkCurDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChSinkCurDayEntry 1}optIfOChSinkCurDayLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
current 24-hour interval."::={ optIfOChSinkCurDayEntry 2}optIfOChSinkCurDayHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
current 24-hour interval."::={ optIfOChSinkCurDayEntry 3}-- OCh sink previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.optIfOChSinkPrevDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChSinkPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OCh sink performance monitoring information for
the previous 24-hour interval."::={ optIfOCh 5}
optIfOChSinkPrevDayEntry OBJECT-TYPESYNTAX OptIfOChSinkPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OCh sink performance
monitoring information of an interface for the previous
24-hour interval."INDEX{ ifIndex }::={ optIfOChSinkPrevDayTable 1}
OptIfOChSinkPrevDayEntry ::=SEQUENCE{
optIfOChSinkPrevDaySuspectedFlag TruthValue,
optIfOChSinkPrevDayLastInputPower Integer32,
optIfOChSinkPrevDayLowInputPower Integer32,
optIfOChSinkPrevDayHighInputPower Integer32}optIfOChSinkPrevDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChSinkPrevDayEntry 1}optIfOChSinkPrevDayLastInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the input during the
previous 24-hour interval."::={ optIfOChSinkPrevDayEntry 2}optIfOChSinkPrevDayLowInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the input during the
previous 24-hour interval."::={ optIfOChSinkPrevDayEntry 3}optIfOChSinkPrevDayHighInputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the input during the
previous 24-hour interval."::={ optIfOChSinkPrevDayEntry 4}-- OCh source current table
-- Contains data for the current 15-minute performance monitoring
-- interval.optIfOChSrcCurrentTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChSrcCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OCh source performance monitoring information for
the current 15-minute interval."::={ optIfOCh 6}optIfOChSrcCurrentEntry OBJECT-TYPESYNTAX OptIfOChSrcCurrentEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OCh source performance
monitoring information of an interface for the current
15-minute interval."INDEX{ ifIndex }::={ optIfOChSrcCurrentTable 1}
OptIfOChSrcCurrentEntry ::=SEQUENCE{
optIfOChSrcCurrentSuspectedFlag TruthValue,
optIfOChSrcCurrentOutputPower Integer32,
optIfOChSrcCurrentLowOutputPower Integer32,
optIfOChSrcCurrentHighOutputPower Integer32,
optIfOChSrcCurrentLowerOutputPowerThreshold Integer32,
optIfOChSrcCurrentUpperOutputPowerThreshold Integer32}optIfOChSrcCurrentSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChSrcCurrentEntry 1}optIfOChSrcCurrentOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The optical power monitored at the output."::={ optIfOChSrcCurrentEntry 2}optIfOChSrcCurrentLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 15-minute interval."::={ optIfOChSrcCurrentEntry 3}optIfOChSrcCurrentHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 15-minute interval."::={ optIfOChSrcCurrentEntry 4}optIfOChSrcCurrentLowerOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The lower limit threshold on output power. If
optIfOChSrcCurrentOutputPower drops to this value or below,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChSrcCurrentEntry 5}optIfOChSrcCurrentUpperOutputPowerThreshold OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The upper limit threshold on output power. If
optIfOChSrcCurrentOutputPower reaches or exceeds this value,
a Threshold Crossing Alert (TCA) should be sent."::={ optIfOChSrcCurrentEntry 6}-- OCh source interval table
-- Contains data for previous 15-minute performance monitoring
-- intervals.optIfOChSrcIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChSrcIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of historical OCh source performance monitoring
information."::={ optIfOCh 7}optIfOChSrcIntervalEntry OBJECT-TYPESYNTAX OptIfOChSrcIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OCh source performance
monitoring information of an interface during a particular
historical interval."INDEX{ ifIndex, optIfOChSrcIntervalNumber }::={ optIfOChSrcIntervalTable 1}
OptIfOChSrcIntervalEntry ::=SEQUENCE{
optIfOChSrcIntervalNumber OptIfIntervalNumber,
optIfOChSrcIntervalSuspectedFlag TruthValue,
optIfOChSrcIntervalLastOutputPower Integer32,
optIfOChSrcIntervalLowOutputPower Integer32,
optIfOChSrcIntervalHighOutputPower Integer32}optIfOChSrcIntervalNumber OBJECT-TYPESYNTAXOptIfIntervalNumberMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Uniquely identifies the interval."::={ optIfOChSrcIntervalEntry 1}optIfOChSrcIntervalSuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChSrcIntervalEntry 2}optIfOChSrcIntervalLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output during the
interval."::={ optIfOChSrcIntervalEntry 3}optIfOChSrcIntervalLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
interval."::={ optIfOChSrcIntervalEntry 4}optIfOChSrcIntervalHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
interval."::={ optIfOChSrcIntervalEntry 5}-- OCh source current day table
-- Contains data for the current 24-hour performance
-- monitoring interval.optIfOChSrcCurDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChSrcCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OCh source performance monitoring information for
the current 24-hour interval."::={ optIfOCh 8}optIfOChSrcCurDayEntry OBJECT-TYPESYNTAX OptIfOChSrcCurDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OCh source performance
monitoring information of an interface for the current
24-hour interval."INDEX{ ifIndex }::={ optIfOChSrcCurDayTable 1}
OptIfOChSrcCurDayEntry ::=SEQUENCE{
optIfOChSrcCurDaySuspectedFlag TruthValue,
optIfOChSrcCurDayLowOutputPower Integer32,
optIfOChSrcCurDayHighOutputPower Integer32}optIfOChSrcCurDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChSrcCurDayEntry 1}optIfOChSrcCurDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The lowest optical power monitored at the output during the
current 24-hour interval."::={ optIfOChSrcCurDayEntry 2}optIfOChSrcCurDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
current 24-hour interval."::={ optIfOChSrcCurDayEntry 3}-- OCh source previous day table
-- Contains data for the previous 24-hour performance
-- monitoring interval.optIfOChSrcPrevDayTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOChSrcPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OCh source performance monitoring information for
the previous 24-hour interval."::={ optIfOCh 9}optIfOChSrcPrevDayEntry OBJECT-TYPESYNTAX OptIfOChSrcPrevDayEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OCh source performance
monitoring information of an interface for the previous
24-hour interval."INDEX{ ifIndex }::={ optIfOChSrcPrevDayTable 1}
OptIfOChSrcPrevDayEntry ::=SEQUENCE{
optIfOChSrcPrevDaySuspectedFlag TruthValue,
optIfOChSrcPrevDayLastOutputPower Integer32,
optIfOChSrcPrevDayLowOutputPower Integer32,
optIfOChSrcPrevDayHighOutputPower Integer32}optIfOChSrcPrevDaySuspectedFlag OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"If true, the data in this entry may be unreliable."::={ optIfOChSrcPrevDayEntry 1}optIfOChSrcPrevDayLastOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last optical power monitored at the output during the
previous 24-hour interval."::={ optIfOChSrcPrevDayEntry 2}optIfOChSrcPrevDayLowOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The lowest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOChSrcPrevDayEntry 3}optIfOChSrcPrevDayHighOutputPower OBJECT-TYPESYNTAXInteger32UNITS"0.1 dbm"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The highest optical power monitored at the output during the
previous 24-hour interval."::={ optIfOChSrcPrevDayEntry 4}-- the optIfOTUk group
-- This group handles the configuration
-- information for OTUk layers.-- OTUk config tableoptIfOTUkConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfOTUkConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of OTUk configuration information."::={ optIfOTUk 1}optIfOTUkConfigEntry OBJECT-TYPESYNTAX OptIfOTUkConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains OTUk configuration
information of an interface."INDEX{ ifIndex }::={ optIfOTUkConfigTable 1}
OptIfOTUkConfigEntry ::=SEQUENCE{
optIfOTUkDirectionality OptIfDirectionality,
optIfOTUkBitRateK OptIfBitRateK,
optIfOTUkTraceIdentifierTransmitted OptIfTxTI,
optIfOTUkDAPIExpected OptIfExDAPI,
optIfOTUkSAPIExpected OptIfExSAPI,
optIfOTUkTraceIdentifierAccepted OptIfAcTI,
optIfOTUkTIMDetMode OptIfTIMDetMode,
optIfOTUkTIMActEnabled TruthValue,
optIfOTUkDEGThr OptIfDEGThr,
optIfOTUkDEGM OptIfDEGM,
optIfOTUkSinkAdaptActive TruthValue,
optIfOTUkSourceAdaptActive TruthValue,
optIfOTUkSinkFECEnabled TruthValue,
optIfOTUkCurrentStatus BITS}optIfOTUkDirectionality OBJECT-TYPESYNTAXOptIfDirectionalityMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the directionality of the entity."::={ optIfOTUkConfigEntry 1}optIfOTUkBitRateK OBJECT-TYPESYNTAXOptIfBitRateKMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the bit rate of the entity."::={ optIfOTUkConfigEntry 2}optIfOTUkTraceIdentifierTransmitted OBJECT-TYPESYNTAXOptIfTxTIMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The trace identifier transmitted.
This object is applicable when optIfOTUkDirectionality
has the value source(2) or bidirectional(3). It must not
be instantiated in rows where optIfOTUkDirectionality
has the value sink(1).
If no value is ever set by a management entity for this
object, system-specific default value will be used.
Any implementation that instantiates this object must
document the system-specific default value or how it
is derived."::={ optIfOTUkConfigEntry 3}optIfOTUkDAPIExpected OBJECT-TYPESYNTAXOptIfExDAPIMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The DAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2).
This object has no effect when optIfOTUkTIMDetMode has
the value off(1)."::={ optIfOTUkConfigEntry 4}optIfOTUkSAPIExpected OBJECT-TYPESYNTAXOptIfExSAPIMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The SAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2).
This object has no effect when optIfOTUkTIMDetMode has
the value off(1)."::={ optIfOTUkConfigEntry 5}optIfOTUkTraceIdentifierAccepted OBJECT-TYPESYNTAXOptIfAcTIMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The actual trace identifier accepted.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2).
The value of this object is unspecified when
optIfOTUkCurrentStatus indicates a near-end defect
(i.e., ssf(3), lof(4), ais(5), lom(6)) that prevents
extraction of the trace message."::={ optIfOTUkConfigEntry 6}optIfOTUkTIMDetMode OBJECT-TYPESYNTAXOptIfTIMDetModeMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2).
The default value of this object is off(1)."::={ optIfOTUkConfigEntry 7}optIfOTUkTIMActEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2).
This object has no effect when optIfOTUkTIMDetMode has
the value off(1).
The default value of this object is false(2)."::={ optIfOTUkConfigEntry 8}optIfOTUkDEGThr OBJECT-TYPESYNTAXOptIfDEGThrUNITS"percentage"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to optIfOTUkDEGThr.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2).
The default value of this object is Severely Errored Second
(SES) Estimator (See ITU-T G.7710)."::={ optIfOTUkConfigEntry 9}optIfOTUkDEGM OBJECT-TYPESYNTAXOptIfDEGMMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if optIfOTUkDEGM
consecutive bad PM Seconds are detected.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2).
The default value of this object is 7 (See ITU-T G.7710)."::={ optIfOTUkConfigEntry 10}optIfOTUkSinkAdaptActive OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates whether the sink adaptation function is activated or
not.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2).
The default value of this object is false(2)."::={ optIfOTUkConfigEntry 11}optIfOTUkSourceAdaptActive OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates whether the source adaptation function is activated or
not.
This object is only applicable to the source function, i.e.,
only when optIfOTUkDirectionality has the value source(2)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value sink(1).
The default value of this object is false(2)."::={ optIfOTUkConfigEntry 12}optIfOTUkSinkFECEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"If Forward Error Correction (FEC) is supported, this object
indicates whether FEC at the OTUk sink adaptation function is
enabled or not.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2).
The default value of this object is true(1)."::={ optIfOTUkConfigEntry 13}optIfOTUkCurrentStatus OBJECT-TYPESYNTAXBITS{tim(0),deg(1),bdi(2),ssf(3),lof(4),ais(5),lom(6)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the defect condition of the entity, if any.
This object is only applicable to the sink function, i.e.,
only when optIfOTUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfOTUkDirectionality has the value source(2)."::={ optIfOTUkConfigEntry 14}
-- GCC0 config tableoptIfGCC0ConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfGCC0ConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of GCC0 configuration information."::={ optIfOTUk 2}optIfGCC0ConfigEntry OBJECT-TYPESYNTAX OptIfGCC0ConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains GCC0 configuration
information of an interface. Each instance must
correspond to an instance of optIfOTUkConfigEntry.
Separate source and/or sink instances may exist
for a given ifIndex value, or a single bidirectional
instance may exist, but a bidirectional instance may
not coexist with a source or sink instance.
Instances of this conceptual row persist across
agent restarts."INDEX{ ifIndex, optIfGCC0Directionality }::={ optIfGCC0ConfigTable 1}
OptIfGCC0ConfigEntry ::=SEQUENCE{
optIfGCC0Directionality OptIfDirectionality,
optIfGCC0Application SnmpAdminString,
optIfGCC0RowStatus RowStatus}optIfGCC0Directionality OBJECT-TYPESYNTAXOptIfDirectionalityMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Indicates the directionality of the entity.
The values source(2) and bidirectional(3) are
not allowed if the corresponding instance of
optIfOTUkDirectionality has the value sink(1).
The values sink(1) and bidirectional(3) are
not allowed if the corresponding instance of
optIfOTUkDirectionality has the value source(2)."::={ optIfGCC0ConfigEntry 1}optIfGCC0Application OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the application transported by the GCC0 entity.
Example applications are ECC, User data channel.
The value of this object may not be changed when
optIfGCC0RowStatus has the value active(1)."::={ optIfGCC0ConfigEntry 2}optIfGCC0RowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This columnar object is used for creating and deleting a
conceptual row of the optIfGCC0 config table.
It is used to model the addGCC0Access and removeGCC0Access
operations of an OTUk_TTP for GCC0 access control as defined
in G.874.1. Setting RowStatus to createAndGo or createAndWait
implies addGCC0Access. Setting RowStatus to destroy implies
removeGCC0Access."::={ optIfGCC0ConfigEntry 3}-- the optIfODUk group
-- This group handles the configuration information
-- for the ODUk layers.-- ODUk config tableoptIfODUkConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfODUkConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of ODUk configuration information."::={ optIfODUk 1}optIfODUkConfigEntry OBJECT-TYPESYNTAX OptIfODUkConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"A conceptual row that contains ODUk configuration
information of an interface."INDEX{ ifIndex }::={ optIfODUkConfigTable 1}
OptIfODUkConfigEntry ::=SEQUENCE{
optIfODUkDirectionality OptIfDirectionality,
optIfODUkBitRateK OptIfBitRateK,
optIfODUkTcmFieldsInUse BITS,
optIfODUkPositionSeqCurrentSize Unsigned32,
optIfODUkTtpPresent TruthValue}optIfODUkDirectionality OBJECT-TYPESYNTAXOptIfDirectionalityMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the directionality of the entity."::={ optIfODUkConfigEntry 1}optIfODUkBitRateK OBJECT-TYPESYNTAXOptIfBitRateKMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the bit rate of the entity."::={ optIfODUkConfigEntry 2}optIfODUkTcmFieldsInUse OBJECT-TYPESYNTAXBITS{tcmField1(0),tcmField2(1),tcmField3(2),tcmField4(3),tcmField5(4),tcmField6(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the TCM field(s) that are currently in use.
The positions of the bits correspond to the TCM fields.
A bit that is set to 1 means that the corresponding TCM
field is used. This object will be updated when rows are
created in or deleted from the optIfODUkTConfigTable, or
the optIfODUkTNimConfigTable."::={ optIfODUkConfigEntry 3}optIfODUkPositionSeqCurrentSize OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable indicates the current size of the position
sequence (i.e., number of TCM function and/or GCC12
access that have been created in the ODUk interface).
When the value of this variable is greater than zero,
it means that one or more TCM function and/or GCC12
access have been created in the ODUk interface. In this
case, there will be as many rows in the
optIfODUkPositionSeqTable as the value of
optIfODUkPositionSeqCurrentSize corresponding to this
ODUk interface, one row for each TCM function or GCC12
access. The position of the TCM function and/or
GCC12 access within the sequence is indicated by the
optIfODUkPositionSeqPosition variable in
optIfODUkPositionSeqTable.
The optIfODUkPositionSeqTable also provides pointers
to the corresponding TCM function (optIfODUkT) and
GCC12 access (optIfGCC12) entities."::={ optIfODUkConfigEntry 4}optIfODUkTtpPresent OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object has the value true(1) if the ifEntry under which
it is instantiated contains an ODUk Trail Termination Point,
i.e., is the endpoint of an ODUk path. In that case there
will be a corresponding row in the ODUk TTP config table and
it will not be possible to create corresponding rows in the
ODUk NIM config table. This object has the value false(2)
if the ifEntry under which it is instantiated contains an
intermediate ODUk Connection Termination Point. In that case
there is no corresponding row in the ODUk TTP config table,
but it will be possible to create corresponding rows in the
ODUk NIM config table. This object also affects the allowable
options in rows created in the GCC12 config table and in the
ODUkT config table, as specified in the DESCRIPTION clauses
of the columns in those tables."::={ optIfODUkConfigEntry 5}-- ODUk Trail Termination Point (TTP) config tableoptIfODUkTtpConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfODUkTtpConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of ODUk TTP configuration information."::={ optIfODUk 2}optIfODUkTtpConfigEntry OBJECT-TYPESYNTAX OptIfODUkTtpConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains ODUk TTP configuration
information of an interface."INDEX{ ifIndex }::={ optIfODUkTtpConfigTable 1}
OptIfODUkTtpConfigEntry ::=SEQUENCE{
optIfODUkTtpTraceIdentifierTransmitted OptIfTxTI,
optIfODUkTtpDAPIExpected OptIfExDAPI,
optIfODUkTtpSAPIExpected OptIfExSAPI,
optIfODUkTtpTraceIdentifierAccepted OptIfAcTI,
optIfODUkTtpTIMDetMode OptIfTIMDetMode,
optIfODUkTtpTIMActEnabled TruthValue,
optIfODUkTtpDEGThr OptIfDEGThr,
optIfODUkTtpDEGM OptIfDEGM,
optIfODUkTtpCurrentStatus BITS}optIfODUkTtpTraceIdentifierTransmitted OBJECT-TYPESYNTAXOptIfTxTIMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The trace identifier transmitted.
This object is applicable when optIfODUkDirectionality
has the value source(2) or bidirectional(3). It must not
be instantiated in rows where optIfODUkDirectionality
has the value sink(1).
If no value is ever set by a management entity for this
object, system-specific default value will be used.
Any implementation that instantiates this object must
document the system-specific default value or how it
is derived."::={ optIfODUkTtpConfigEntry 1}optIfODUkTtpDAPIExpected OBJECT-TYPESYNTAXOptIfExDAPIMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The DAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when optIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfODUkDirectionality has the value source(2).
This object has no effect when optIfODUkTtpTIMDetMode has
the value off(1)."::={ optIfODUkTtpConfigEntry 2}optIfODUkTtpSAPIExpected OBJECT-TYPESYNTAXOptIfExSAPIMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The SAPI expected by the receiver.
This object is only applicable to the sink function, i.e.,
only when optIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfODUkDirectionality has the value source(2).
This object has no effect when optIfODUkTtpTIMDetMode has
the value off(1)."::={ optIfODUkTtpConfigEntry 3}optIfODUkTtpTraceIdentifierAccepted OBJECT-TYPESYNTAXOptIfAcTIMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The actual trace identifier accepted.
This object is only applicable to the sink function, i.e.,
only when optIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfODUkDirectionality has the value source(2).
The value of this object is unspecified when
optIfODUkTtpCurrentStatus indicates a near-end defect
(i.e., oci(0), lck(1), ssf(5)) that prevents extraction
of the trace message."::={ optIfODUkTtpConfigEntry 4}optIfODUkTtpTIMDetMode OBJECT-TYPESYNTAXOptIfTIMDetModeMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function.
This object is only applicable to the sink function, i.e.,
only when optIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfODUkDirectionality has the value source(2).
The default value of this object is off(1)."::={ optIfODUkTtpConfigEntry 5}optIfODUkTtpTIMActEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled.
This object is only applicable to the sink function, i.e.,
only when optIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfODUkDirectionality has the value source(2).
This object has no effect when optIfODUkTtpTIMDetMode has
the value off(1).
The default value of this object is false(2)."::={ optIfODUkTtpConfigEntry 6}optIfODUkTtpDEGThr OBJECT-TYPESYNTAXOptIfDEGThrUNITS"percentage"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to optIfODUkDEGThr.
This object is only applicable to the sink function, i.e.,
only when optIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfODUkDirectionality has the value source(2).
The default value of this object is Severely Errored Second
(SES) Estimator (See ITU-T G.7710)."::={ optIfODUkTtpConfigEntry 7}optIfODUkTtpDEGM OBJECT-TYPESYNTAXOptIfDEGMMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if optIfODUkDEGM
consecutive bad PM Seconds are detected.
This object is only applicable to the sink function, i.e.,
only when optIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfODUkDirectionality has the value source(2).
The default value of this object is 7 (See ITU-T G.7710)."::={ optIfODUkTtpConfigEntry 8}optIfODUkTtpCurrentStatus OBJECT-TYPESYNTAXBITS{oci(0),lck(1),
tim(2),deg(3),bdi(4),ssf(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the defect condition of the entity, if any.
This object is only applicable to the sink function, i.e.,
only when optIfODUkDirectionality has the value sink(1)
or bidirectional(3). It must not be instantiated in rows
where optIfODUkDirectionality has the value source(2)."::={ optIfODUkTtpConfigEntry 9}-- ODUk Position Sequence tableoptIfODUkPositionSeqTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfODUkPositionSeqEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of ODUk Position Sequence information."::={ optIfODUk 3}optIfODUkPositionSeqEntry OBJECT-TYPESYNTAX OptIfODUkPositionSeqEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains ODUk position sequence
information of an ODUk interface. The ODUk interface
is identified by the ifIndex. Associated with each
ODUk interface there may be one of more conceptual
rows in the optIfODUkPositionSeqTable. Each row
represents a TCM or GCC12 access function within the
associated ODUk interface. Rows of the
optIfODUkPositionSeqTable table are created/deleted
as the result of the creation/deletion of the optIfODUkT
or optIfGCC12 entities."INDEX{ ifIndex, optIfODUkPositionSeqIndex }::={ optIfODUkPositionSeqTable 1}
OptIfODUkPositionSeqEntry ::=SEQUENCE{
optIfODUkPositionSeqIndex Unsigned32,
optIfODUkPositionSeqPosition Unsigned32,
optIfODUkPositionSeqPointer RowPointer}optIfODUkPositionSeqIndex OBJECT-TYPESYNTAXUnsigned32(1..4294967295)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This variable identifies a row in the
optIfODUkPositionSeqTable Table.
Each row of the optIfODUkPositionSeqTable Table
represents a TCM or GCC12 access function within the
associated ODUk interface."::={ optIfODUkPositionSeqEntry 1}optIfODUkPositionSeqPosition OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable indicates the position of the TCM or
GCC12 access function within the sequence of TCMs &
GCC12 access functions of the associated ODUk
interface. The TCM or GCC12 presented by this row is
referenced by the optIfODUkPositionSeqPointer variable."::={ optIfODUkPositionSeqEntry 2}optIfODUkPositionSeqPointer OBJECT-TYPESYNTAXRowPointerMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This variable identifies the TCM or GCC12 access function
by pointing to the corresponding optIfODUkT or optIfGCC12
entity."::={ optIfODUkPositionSeqEntry 3}
-- ODUk Non-intrusive monitoring (Nim) config tableoptIfODUkNimConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfODUkNimConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of ODUkNim configuration information."::={ optIfODUk 4}optIfODUkNimConfigEntry OBJECT-TYPESYNTAX OptIfODUkNimConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains ODUkNim configuration
information of an interface. Each instance must
correspond to an instance of optIfODUkConfigEntry
for which optIfODUkTtpPresent has the value false(2).
Instances of this conceptual row persist across
agent restarts, and read-create columns other
than the status column may be modified while the
row is active."INDEX{ ifIndex, optIfODUkNimDirectionality }::={ optIfODUkNimConfigTable 1}
OptIfODUkNimConfigEntry ::=SEQUENCE{
optIfODUkNimDirectionality OptIfSinkOrSource,
optIfODUkNimDAPIExpected OptIfExDAPI,
optIfODUkNimSAPIExpected OptIfExSAPI,
optIfODUkNimTraceIdentifierAccepted OptIfAcTI,
optIfODUkNimTIMDetMode OptIfTIMDetMode,
optIfODUkNimTIMActEnabled TruthValue,
optIfODUkNimDEGThr OptIfDEGThr,
optIfODUkNimDEGM OptIfDEGM,
optIfODUkNimCurrentStatus BITS,
optIfODUkNimRowStatus RowStatus}optIfODUkNimDirectionality OBJECT-TYPESYNTAXOptIfSinkOrSourceMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies the monitor point for the ODUk Path non-intrusive
monitoring function. The value source(2) is not allowed
if the corresponding instance of optIfODUkDirectionality
has the value sink(1), and the value sink(1) is not allowed
if the corresponding instance of optIfODUkDirectionality
has the value source(2). Either the value sink(1) or
source(2) is allowed if the corresponding instance of
optIfODUkDirectionality has the value bidirectional(3).
The value sink(1) means monitoring at the sink direction
path signal of the ODUk CTP.
The value source(2) means monitoring at the source direction
path signal of the ODUk CTP. Monitoring the source direction
of an ODUk CTP is necessary in those cases where the ODUk CTP
is at an SNCP (Subnetwork Connection Protection) end (e.g., see
Figure I.1.2/G.874.1). If one would like to get the performance
of the protected connection, one cannot use the NIM function
at both ODUk CTP sinks (before the matrix), instead one should
monitor the signal at the source ODUk CTP after the matrix."::={ optIfODUkNimConfigEntry 1}optIfODUkNimDAPIExpected OBJECT-TYPESYNTAXOptIfExDAPIMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The DAPI expected by the receiver.
This object has no effect if optIfODUkNimTIMDetMode has
the value off(1) or sapi(3)."::={ optIfODUkNimConfigEntry 2}optIfODUkNimSAPIExpected OBJECT-TYPESYNTAXOptIfExSAPIMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The SAPI expected by the receiver.
This object has no effect if optIfODUkNimTIMDetMode has
the value off(1) or dapi(2)."::={ optIfODUkNimConfigEntry 3}optIfODUkNimTraceIdentifierAccepted OBJECT-TYPESYNTAXOptIfAcTIMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The actual trace identifier accepted. The value of
this object is unspecified if optIfODUkNimCurrentStatus
has any of the bit positions oci(0), lck(1), or ssf(5)
set or if optIfODUkNimRowStatus has any value other
than active(1)."::={ optIfODUkNimConfigEntry 4}optIfODUkNimTIMDetMode OBJECT-TYPESYNTAXOptIfTIMDetModeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function."::={ optIfODUkNimConfigEntry 5}optIfODUkNimTIMActEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled."::={ optIfODUkNimConfigEntry 6}optIfODUkNimDEGThr OBJECT-TYPESYNTAXOptIfDEGThrUNITS"percentage"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad
if the percentage of detected errored blocks in that second is
greater than or equal to optIfODUkNimDEGThr."::={ optIfODUkNimConfigEntry 7}optIfODUkNimDEGM OBJECT-TYPESYNTAXOptIfDEGMMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if optIfODUkNimDEGM
consecutive bad PM Seconds are detected."::={ optIfODUkNimConfigEntry 8}optIfODUkNimCurrentStatus OBJECT-TYPESYNTAXBITS{oci(0),lck(1),tim(2),deg(3),bdi(4),ssf(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the defect condition of the entity, if
any. The value of this object is unspecified if
optIfODUkNimRowStatus has any value other than
active(1)."::={ optIfODUkNimConfigEntry 9}optIfODUkNimRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This columnar object is used for creating and deleting
a conceptual row of the optIfODUkNim config table.
It is used to model the activateNim and deactivateNim
operations of an OTUk_CTP for non-intrusive monitoring
control as defined in G.874.1. Setting RowStatus to
createAndGo or createAndWait implies activateNim.
Setting RowStatus to destroy implies deactivateNim."::={ optIfODUkNimConfigEntry 10}-- GCC12 config tableoptIfGCC12ConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfGCC12ConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of GCC12 configuration information.
The GCC function processes the GCC overhead bytes passing
through them but leave the remainder of the ODUk overhead
and payload data alone."::={ optIfODUk 5}optIfGCC12ConfigEntry OBJECT-TYPESYNTAX OptIfGCC12ConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains GCC12 configuration
information of an interface. Each instance must
correspond to an instance of optIfODUkConfigEntry.
Separate instances providing GCC1-only access and
GCC2-only access may exist for a given ifIndex value,
or a single instance providing GCC1 + GCC2 may exist,
but a GCC1 + GCC2 instance may not coexist with a
GCC1-only or GCC2-only instance.
Instances of this conceptual row persist across agent
restarts."INDEX{ ifIndex, optIfGCC12Codirectional, optIfGCC12GCCAccess }::={ optIfGCC12ConfigTable 1}
OptIfGCC12ConfigEntry ::=SEQUENCE{
optIfGCC12Codirectional TruthValue,
optIfGCC12GCCAccess INTEGER,
optIfGCC12GCCPassThrough TruthValue,
optIfGCC12Application SnmpAdminString,
optIfGCC12RowStatus RowStatus}optIfGCC12Codirectional OBJECT-TYPESYNTAXTruthValueMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Indicates the directionality of the GCC12 termination with
respect to the associated ODUk CTP. The value true(1) means
that the sink part of the GCC12 extracts COMMS data from the
signal at the input to the ODUk CTP sink and the source part
of the GCC12 inserts COMMS data into the signal at the output
of the ODUk CTP source. The value false(2) means that the
sink part of the GCC12 extracts COMMS data from the signal at
the output of the ODUk CTP source and the source part of the
GCC12 inserts COMMS data into the signal at the input of the
ODUk CTP sink. This attribute may assume either value when
the corresponding instance of optIfODUkTtpPresent has the
value false(2). When the value of the corresponding instance
of optIfODUkTtpPresent is true(1) then the only value allowed
for this attribute is true(1)."::={ optIfGCC12ConfigEntry 1}optIfGCC12GCCAccess OBJECT-TYPESYNTAXINTEGER{gcc1 (1),gcc2 (2),gcc1and2 (3)}MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Indicates the GCC access represented by the entity."::={ optIfGCC12ConfigEntry 2}optIfGCC12GCCPassThrough OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Controls whether the selected GCC overhead bytes are passed
through or modified. The value true(1) means that the selected
GCC overhead bytes are passed through unmodified from the ODUk
CTP input to the ODUk CTP output. The value false(2) means that
the selected GCC overhead bytes are set to zero at the ODUk CTP
output after the extraction of the COMMS data. This object has
no effect if the corresponding instance of optIfODUkTtpPresent
has the value true(1).
The value of this object may not be changed when
optIfGCC12RowStatus has the value active(1)."::={ optIfGCC12ConfigEntry 3}optIfGCC12Application OBJECT-TYPESYNTAXSnmpAdminStringMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the application transported by the GCC12 entity.
Example applications are ECC, User data channel.
The value of this object may not be changed when
optIfGCC12RowStatus has the value active(1)."::={ optIfGCC12ConfigEntry 4}optIfGCC12RowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This columnar object is used for creating and deleting
a conceptual row of the optIfGCC12 config table. It is
used to model the addGCC12Access and removeGCC12Access
operations of an ODUk_CTP or ODUk_TTP for GCC12 access
control as defined in G.874.1. Setting RowStatus to
createAndGo or createAndWait implies addGCC12Access.
Setting RowStatus to destroy implies removeGCC12Access.
Successful addition/removal of the GCC12 access function
will result in updating the
optIfODUkPositionSeqCurrentSize variable and the
optIfODUkPositionSeqTable table of the associated
ODUk entry in the optIfODUkConfigTable."::={ optIfGCC12ConfigEntry 5}-- the optIfODUkT group
-- This group handles the configuration information
-- for the ODUkT layers.-- ODUkT config tableoptIfODUkTConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfODUkTConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of ODUkT configuration information."::={ optIfODUkT 1}optIfODUkTConfigEntry OBJECT-TYPESYNTAX OptIfODUkTConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains ODUkT configuration
information of an interface. Each instance must
correspond to an instance of optIfODUkConfigEntry.
Rows in this table are mutually exclusive with rows
in the ODUkT NIM config table -- in other words, this
row object may not be instantiated for a given pair
of ifIndex and TCM field values if a corresponding
instance of optIfODUkTNimConfigEntry already exists.
Instances of this conceptual row persist across agent
restarts. Except where noted otherwise, read-create
columns other than the status column may be modified
while the row is active."INDEX{ ifIndex, optIfODUkTTcmField, optIfODUkTCodirectional }::={ optIfODUkTConfigTable 1}
OptIfODUkTConfigEntry ::=SEQUENCE{
optIfODUkTTcmField Unsigned32,
optIfODUkTCodirectional TruthValue,
optIfODUkTTraceIdentifierTransmitted OptIfTxTI,
optIfODUkTDAPIExpected OptIfExDAPI,
optIfODUkTSAPIExpected OptIfExSAPI,
optIfODUkTTraceIdentifierAccepted OptIfAcTI,
optIfODUkTTIMDetMode OptIfTIMDetMode,
optIfODUkTTIMActEnabled TruthValue,
optIfODUkTDEGThr OptIfDEGThr,
optIfODUkTDEGM OptIfDEGM,
optIfODUkTSinkMode INTEGER,
optIfODUkTSinkLockSignalAdminState INTEGER,
optIfODUkTSourceLockSignalAdminState INTEGER,
optIfODUkTCurrentStatus BITS,
optIfODUkTRowStatus RowStatus}optIfODUkTTcmField OBJECT-TYPESYNTAXUnsigned32(1..6)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Indicates the tandem connection monitoring
field of the ODUk OH. Valid values are
integers from 1 to 6."::={ optIfODUkTConfigEntry 1}optIfODUkTCodirectional OBJECT-TYPESYNTAXTruthValueMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Indicates the directionality of the ODUkT termination point with
respect to the associated ODUk CTP. The value true(1) means
that the sink part of the ODUkT TP extracts TCM data from the
signal at the input to the ODUk CTP sink and the source part
of the ODUkT TP inserts TCM data into the signal at the output
of the ODUk CTP source. The value false(2) means that the
sink part of the ODUkT TP extracts TCM data from the signal at
the output of the ODUk CTP source and the source part of the
ODUkT TP inserts TCM data into the signal at the input of the
ODUk CTP sink. This attribute may assume either value when
the corresponding instance of optIfODUkTtpPresent has the
value false(2). When the value of the corresponding instance
of optIfODUkTtpPresent is true(1) then the only value allowed
for this attribute is true(1)."::={ optIfODUkTConfigEntry 2}optIfODUkTTraceIdentifierTransmitted OBJECT-TYPESYNTAXOptIfTxTIMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The trace identifier transmitted.
This object is applicable only to the following three cases.
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value false(2), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value true(1).
It must not be instantiated in rows for all other cases."::={ optIfODUkTConfigEntry 3}optIfODUkTDAPIExpected OBJECT-TYPESYNTAXOptIfExDAPIMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The DAPI expected by the receiver.
This object is applicable only to the following three cases.
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
This object has no effect when optIfODUkTTIMDetMode has
the value off(1)."::={ optIfODUkTConfigEntry 4}optIfODUkTSAPIExpected OBJECT-TYPESYNTAXOptIfExSAPIMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The SAPI expected by the receiver.
This object is applicable only to the following three cases.
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
This object has no effect when optIfODUkTTIMDetMode has
the value off(1)."
::={ optIfODUkTConfigEntry 5}optIfODUkTTraceIdentifierAccepted OBJECT-TYPESYNTAXOptIfAcTIMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The actual trace identifier accepted.
This object is applicable only to the following three cases.
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
The value of this object is unspecified when
optIfODUkTCurrentStatus indicates a near-end defect
(i.e., oci(0), lck(1), ssf(5)) that prevents extraction
of the trace message."::={ optIfODUkTConfigEntry 6}optIfODUkTTIMDetMode OBJECT-TYPESYNTAXOptIfTIMDetModeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function.
This object is applicable only to the following three cases.
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
The default value of this object is off(1)."::={ optIfODUkTConfigEntry 7}optIfODUkTTIMActEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled.
This object is applicable only to the following three cases.
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
This object has no effect when optIfODUkTTIMDetMode has
the value off(1).
The default value of this object is false(2)."::={ optIfODUkTConfigEntry 8}optIfODUkTDEGThr OBJECT-TYPESYNTAXOptIfDEGThrUNITS"percentage"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to optIfODUkTDEGThr.
This object is applicable only to the following three cases.
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
The default value of this object is Severely Errored Second
(SES) Estimator (See ITU-T G.7710)."::={ optIfODUkTConfigEntry 9}optIfODUkTDEGM OBJECT-TYPESYNTAXOptIfDEGMMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if optIfODUkTDEGM
consecutive bad PM Seconds are detected.
This object is applicable only to the following three cases.
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases.
The default value of this object is 7 (See ITU-T G.7710)."::={ optIfODUkTConfigEntry 10}optIfODUkTSinkMode OBJECT-TYPESYNTAXINTEGER{operational (1),monitor (2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This variable specifies the TCM mode at the entity.
The value operational(1) means that TCM Overhead (TCMOH)
processes (see ITU-T G.798) shall be
performed and consequent actions for AIS, Trail
Signal Fail (TSF), Trail Signal Degraded (TSD) shall be
initiated in case of defects.
The value monitor(2) means that TCMOH processes shall be
performed but consequent actions for AIS, Trail
Server Failure (TSF), Trail Server Degraded (TSD) shall _not_ be
initiated in case of defects.
This object is applicable only when the value of
optIfODUkTtpPresent is false(2) and also either one of the
following three cases holds:
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases."::={ optIfODUkTConfigEntry 11}optIfODUkTSinkLockSignalAdminState OBJECT-TYPESYNTAXINTEGER{locked(1),normal(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Provides the capability to provision the LOCK signal, which
is one of the ODUk maintenance signals, at the ODUKT sink. When
a Tandem Connection endpoint is set to admin state locked,
it inserts the ODUk-LCK signal in the sink direction.
This object is applicable only when the value of
optIfODUkTtpPresent is false(2) and also either one of the
following three cases holds:
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases."::={ optIfODUkTConfigEntry 12}optIfODUkTSourceLockSignalAdminState OBJECT-TYPESYNTAXINTEGER{locked(1),normal(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Provides the capability to provision the LOCK signal, which
is one of the ODUk maintenance signals, at the source.
When a Tandem Connection endpoint is set to admin state
locked, it inserts the ODUk-LCK signal in the source
direction.
This object is applicable only when either one of the
following three cases holds:
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value false(2), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value true(1).
It must not be instantiated in rows for all other cases."::={ optIfODUkTConfigEntry 13}optIfODUkTCurrentStatus OBJECT-TYPESYNTAXBITS{oci(0),
lck(1),tim(2),deg(3),bdi(4),ssf(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the defect condition of the entity, if any.
This object is applicable only when either one of the
following three cases holds:
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It must not be instantiated in rows for all other cases."::={ optIfODUkTConfigEntry 14}optIfODUkTRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This columnar object is used for creating and deleting a
conceptual row of the optIfODUkT config table.
It is used to model the addTCM and removeTCM operations of an
ODUk_CTP or ODUk_TTP for Tandem connection monitoring as defined
in ITU-T G.874.1.
Setting RowStatus to createAndGo or createAndWait implies addTCM.
Setting RowStatus to destroy implies removeTCM.
Successful addition/removal of TCM will result in updating the
optIfODUkTcmFieldsInUse and optIfODUkPositionSeqCurrentSize
variables and the optIfODUkPositionSeqTable table of the
associated ODUk entry in the optIfODUkConfigTable."::={ optIfODUkTConfigEntry 15}-- ODUkT Non-intrusive monitoring (Nim) config tableoptIfODUkTNimConfigTable OBJECT-TYPESYNTAXSEQUENCEOF OptIfODUkTNimConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table of ODUkTNim configuration information."::={ optIfODUkT 2}optIfODUkTNimConfigEntry OBJECT-TYPESYNTAX OptIfODUkTNimConfigEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A conceptual row that contains ODUkTNim configuration
information of an interface. Each instance must
correspond to an instance of optIfODUkConfigEntry.
Rows in this table are mutually exclusive with rows
in the ODUkT config table -- in other words, this
row object may not be instantiated for a given pair
of ifIndex and TCM field values if a corresponding
instance of optIfODUkTConfigEntry already exists.
Instances of this conceptual row persist across
agent restarts, and read-create columns other
than the status column may be modified while the
row is active."INDEX{ifIndex, optIfODUkTNimTcmField, optIfODUkTNimDirectionality}::={ optIfODUkTNimConfigTable 1}
OptIfODUkTNimConfigEntry ::=SEQUENCE{
optIfODUkTNimTcmField Unsigned32,
optIfODUkTNimDirectionality OptIfSinkOrSource,
optIfODUkTNimDAPIExpected OptIfExDAPI,
optIfODUkTNimSAPIExpected OptIfExSAPI,
optIfODUkTNimTraceIdentifierAccepted OptIfAcTI,
optIfODUkTNimTIMDetMode OptIfTIMDetMode,
optIfODUkTNimTIMActEnabled TruthValue,
optIfODUkTNimDEGThr OptIfDEGThr,
optIfODUkTNimDEGM OptIfDEGM,
optIfODUkTNimCurrentStatus BITS,
optIfODUkTNimRowStatus RowStatus}optIfODUkTNimTcmField OBJECT-TYPESYNTAXUnsigned32(1..6)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Indicates the tandem connection monitoring
field of the ODUk OH on which non-intrusive monitoring
is performed. Valid values are
integers from 1 to 6."::={ optIfODUkTNimConfigEntry 1}optIfODUkTNimDirectionality OBJECT-TYPESYNTAXOptIfSinkOrSourceMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Specifies the monitor point for the ODUk TCM non-intrusive
monitoring function. The value source(2) is not allowed
if the corresponding instance of optIfODUkDirectionality
has the value sink(1), and the value sink(1) is not allowed
if the corresponding instance of optIfODUkDirectionality
has the value source(2). Either the value sink(1) or
source(2) is allowed if the corresponding instance of
optIfODUkDirectionality has the value bidirectional(3).
The value sink(1) means monitoring at the sink direction
TCM signal of the ODUk CTP.
The value source(2) means monitoring at the source direction
path signal of the ODUk CTP."::={ optIfODUkTNimConfigEntry 2}optIfODUkTNimDAPIExpected OBJECT-TYPESYNTAXOptIfExDAPIMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The DAPI expected by the receiver.
This object has no effect if optIfODUkTNimTIMDetMode has
the value off(1) or sapi(3)."::={ optIfODUkTNimConfigEntry 3}optIfODUkTNimSAPIExpected OBJECT-TYPESYNTAXOptIfExSAPIMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The SAPI expected by the receiver.
This object has no effect if optIfODUkTNimTIMDetMode has
the value off(1) or dapi(2)."::={ optIfODUkTNimConfigEntry 4}optIfODUkTNimTraceIdentifierAccepted OBJECT-TYPESYNTAXOptIfAcTIMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The actual trace identifier accepted. The value of
this object is unspecified if optIfODUkTNimCurrentStatus
has any of the bit positions oci(0), lck(1), or ssf(5)
set or if optIfODUkTNimRowStatus has any value other
than active(1)."::={ optIfODUkTNimConfigEntry 5}optIfODUkTNimTIMDetMode OBJECT-TYPESYNTAXOptIfTIMDetModeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the mode of the Trace Identifier Mismatch (TIM)
Detection function."::={ optIfODUkTNimConfigEntry 6}optIfODUkTNimTIMActEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates whether the Trace Identifier Mismatch (TIM)
Consequent Action function is enabled."::={ optIfODUkTNimConfigEntry 7}optIfODUkTNimDEGThr OBJECT-TYPESYNTAXOptIfDEGThrUNITS"percentage"
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a performance
monitoring (PM) Second to be bad. A PM Second is declared bad if
the percentage of detected errored blocks in that second is
greater than or equal to optIfODUkTNimDEGThr."::={ optIfODUkTNimConfigEntry 8}optIfODUkTNimDEGM OBJECT-TYPESYNTAXOptIfDEGMMAX-ACCESSread-createSTATUScurrentDESCRIPTION"Indicates the threshold level for declaring a Degraded Signal
defect (dDEG). A dDEG shall be declared if optIfODUkTNimDEGM
consecutive bad PM Seconds are detected."::={ optIfODUkTNimConfigEntry 9}optIfODUkTNimCurrentStatus OBJECT-TYPESYNTAXBITS{oci(0),lck(1),tim(2),deg(3),bdi(4),ssf(5)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Indicates the defect condition of the entity, if any.
The value of this object is unspecified if
optIfODUkTNimRowStatus has any value other than
active(1)."::={ optIfODUkTNimConfigEntry 10}optIfODUkTNimRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This columnar object is used for creating and deleting a
conceptual row of the optIfODUkTNim config table.
It is used to model the addTCM and removeTCM operations of an
ODUk_CTP or ODUk_TTP for non-intrusive Tandem connection
monitoring as defined in ITU-T G.874.1.
Setting RowStatus to createAndGo or createAndWait implies addTCM.
Setting RowStatus to destroy implies removeTCM.
Successful addition/removal of Nim TCM will result in updating
the optIfODUkPositionSeqCurrentSize variable and the
optIfODUkPositionSeqTable table of the associated ODUk entry
in the optIfODUkConfigTable."::={ optIfODUkTNimConfigEntry 11}-- units of conformanceoptIfOTMnGroup OBJECT-GROUPOBJECTS{
optIfOTMnOrder,
optIfOTMnReduced,
optIfOTMnBitRates,
optIfOTMnInterfaceType,
optIfOTMnTcmMax,
optIfOTMnOpticalReach
}STATUScurrentDESCRIPTION"A collection of OTMn structure information objects."::={ optIfGroups 1}optIfPerfMonGroup OBJECT-GROUPOBJECTS{
optIfPerfMonCurrentTimeElapsed,
optIfPerfMonCurDayTimeElapsed,
optIfPerfMonIntervalNumIntervals,
optIfPerfMonIntervalNumInvalidIntervals
}STATUScurrentDESCRIPTION"A collection of performance monitoring interval objects."::={ optIfGroups 2}optIfOTSnCommonGroup OBJECT-GROUPOBJECTS{
optIfOTSnDirectionality
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all OTSn interfaces."::={ optIfGroups 3}optIfOTSnSourceGroupFull OBJECT-GROUPOBJECTS{
optIfOTSnTraceIdentifierTransmitted
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to full-functionality/IaDI OTSn
interfaces that support source functions."::={ optIfGroups 4}optIfOTSnAPRStatusGroup OBJECT-GROUPOBJECTS{
optIfOTSnAprStatus
}STATUScurrentDESCRIPTION"A collection of objects applicable to
OTSn interfaces that support Automatic
Power Reduction functions."::={ optIfGroups 5}optIfOTSnAPRControlGroup OBJECT-GROUPOBJECTS{
optIfOTSnAprControl
}STATUScurrentDESCRIPTION"A collection of objects applicable to
OTSn interfaces that provide Automatic
Power Reduction control functions."::={ optIfGroups 6}optIfOTSnSinkGroupBasic OBJECT-GROUPOBJECTS{
optIfOTSnCurrentStatus
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all OTSn interfaces that
support sink functions."::={ optIfGroups 7}optIfOTSnSinkGroupFull OBJECT-GROUPOBJECTS{
optIfOTSnDAPIExpected,
optIfOTSnSAPIExpected,
optIfOTSnTraceIdentifierAccepted,
optIfOTSnTIMDetMode,
optIfOTSnTIMActEnabled
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to full-functionality/IaDI OTSn
interfaces that support sink functions."::={ optIfGroups 8}optIfOTSnSinkPreOtnPMGroup OBJECT-GROUPOBJECTS{
optIfOTSnSinkCurrentSuspectedFlag,
optIfOTSnSinkCurrentInputPower,
optIfOTSnSinkCurrentLowInputPower,
optIfOTSnSinkCurrentHighInputPower,
optIfOTSnSinkCurrentOutputPower,
optIfOTSnSinkCurrentLowOutputPower,
optIfOTSnSinkCurrentHighOutputPower,
optIfOTSnSinkIntervalSuspectedFlag,
optIfOTSnSinkIntervalLastInputPower,
optIfOTSnSinkIntervalLowInputPower,
optIfOTSnSinkIntervalHighInputPower,
optIfOTSnSinkIntervalLastOutputPower,
optIfOTSnSinkIntervalLowOutputPower,
optIfOTSnSinkIntervalHighOutputPower,
optIfOTSnSinkCurDaySuspectedFlag,
optIfOTSnSinkCurDayLowInputPower,
optIfOTSnSinkCurDayHighInputPower,
optIfOTSnSinkCurDayLowOutputPower,
optIfOTSnSinkCurDayHighOutputPower,
optIfOTSnSinkPrevDaySuspectedFlag,
optIfOTSnSinkPrevDayLastInputPower,
optIfOTSnSinkPrevDayLowInputPower,
optIfOTSnSinkPrevDayHighInputPower,
optIfOTSnSinkPrevDayLastOutputPower,
optIfOTSnSinkPrevDayLowOutputPower,
optIfOTSnSinkPrevDayHighOutputPower
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
objects applicable to OTSn interfaces that
support sink functions."::={ optIfGroups 9}optIfOTSnSinkPreOtnPMThresholdGroup OBJECT-GROUP
OBJECTS{
optIfOTSnSinkCurrentLowerInputPowerThreshold,
optIfOTSnSinkCurrentUpperInputPowerThreshold,
optIfOTSnSinkCurrentLowerOutputPowerThreshold,
optIfOTSnSinkCurrentUpperOutputPowerThreshold
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
threshold objects applicable to OTSn interfaces
that support sink functions."::={ optIfGroups 10}optIfOTSnSourcePreOtnPMGroup OBJECT-GROUPOBJECTS{
optIfOTSnSrcCurrentSuspectedFlag,
optIfOTSnSrcCurrentOutputPower,
optIfOTSnSrcCurrentLowOutputPower,
optIfOTSnSrcCurrentHighOutputPower,
optIfOTSnSrcCurrentInputPower,
optIfOTSnSrcCurrentLowInputPower,
optIfOTSnSrcCurrentHighInputPower,
optIfOTSnSrcIntervalSuspectedFlag,
optIfOTSnSrcIntervalLastOutputPower,
optIfOTSnSrcIntervalLowOutputPower,
optIfOTSnSrcIntervalHighOutputPower,
optIfOTSnSrcIntervalLastInputPower,
optIfOTSnSrcIntervalLowInputPower,
optIfOTSnSrcIntervalHighInputPower,
optIfOTSnSrcCurDaySuspectedFlag,
optIfOTSnSrcCurDayLowOutputPower,
optIfOTSnSrcCurDayHighOutputPower,
optIfOTSnSrcCurDayLowInputPower,
optIfOTSnSrcCurDayHighInputPower,
optIfOTSnSrcPrevDaySuspectedFlag,
optIfOTSnSrcPrevDayLastOutputPower,
optIfOTSnSrcPrevDayLowOutputPower,
optIfOTSnSrcPrevDayHighOutputPower,
optIfOTSnSrcPrevDayLastInputPower,
optIfOTSnSrcPrevDayLowInputPower,
optIfOTSnSrcPrevDayHighInputPower
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
objects applicable to OTSn interfaces that
support source functions."::={ optIfGroups 11}optIfOTSnSourcePreOtnPMThresholdGroup OBJECT-GROUPOBJECTS{
optIfOTSnSrcCurrentLowerOutputPowerThreshold,
optIfOTSnSrcCurrentUpperOutputPowerThreshold,
optIfOTSnSrcCurrentLowerInputPowerThreshold,
optIfOTSnSrcCurrentUpperInputPowerThreshold
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
threshold objects applicable to OTSn interfaces
that support source functions."::={ optIfGroups 12}optIfOMSnCommonGroup OBJECT-GROUPOBJECTS{
optIfOMSnDirectionality
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all OMSn interfaces."::={ optIfGroups 13}optIfOMSnSinkGroupBasic OBJECT-GROUPOBJECTS{
optIfOMSnCurrentStatus
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all OMSn interfaces that
support sink functions."::={ optIfGroups 14}optIfOMSnSinkPreOtnPMGroup OBJECT-GROUPOBJECTS{
optIfOMSnSinkCurrentSuspectedFlag,
optIfOMSnSinkCurrentAggregatedInputPower,
optIfOMSnSinkCurrentLowAggregatedInputPower,
optIfOMSnSinkCurrentHighAggregatedInputPower,
optIfOMSnSinkCurrentOutputPower,
optIfOMSnSinkCurrentLowOutputPower,
optIfOMSnSinkCurrentHighOutputPower,
optIfOMSnSinkIntervalSuspectedFlag,
optIfOMSnSinkIntervalLastAggregatedInputPower,
optIfOMSnSinkIntervalLowAggregatedInputPower,
optIfOMSnSinkIntervalHighAggregatedInputPower,
optIfOMSnSinkIntervalLastOutputPower,
optIfOMSnSinkIntervalLowOutputPower,
optIfOMSnSinkIntervalHighOutputPower,
optIfOMSnSinkCurDaySuspectedFlag,
optIfOMSnSinkCurDayLowAggregatedInputPower,
optIfOMSnSinkCurDayHighAggregatedInputPower,
optIfOMSnSinkCurDayLowOutputPower,
optIfOMSnSinkCurDayHighOutputPower,
optIfOMSnSinkPrevDaySuspectedFlag,
optIfOMSnSinkPrevDayLastAggregatedInputPower,
optIfOMSnSinkPrevDayLowAggregatedInputPower,
optIfOMSnSinkPrevDayHighAggregatedInputPower,
optIfOMSnSinkPrevDayLastOutputPower,
optIfOMSnSinkPrevDayLowOutputPower,
optIfOMSnSinkPrevDayHighOutputPower
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
objects applicable to OMSn interfaces that
support sink functions."::={ optIfGroups 15}optIfOMSnSinkPreOtnPMThresholdGroup OBJECT-GROUPOBJECTS{
optIfOMSnSinkCurrentLowerInputPowerThreshold,
optIfOMSnSinkCurrentUpperInputPowerThreshold,
optIfOMSnSinkCurrentLowerOutputPowerThreshold,
optIfOMSnSinkCurrentUpperOutputPowerThreshold
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
threshold objects applicable to OMSn interfaces
that support sink functions."::={ optIfGroups 16}optIfOMSnSourcePreOtnPMGroup OBJECT-GROUPOBJECTS{
optIfOMSnSrcCurrentSuspectedFlag,
optIfOMSnSrcCurrentOutputPower,
optIfOMSnSrcCurrentLowOutputPower,
optIfOMSnSrcCurrentHighOutputPower,
optIfOMSnSrcCurrentAggregatedInputPower,
optIfOMSnSrcCurrentLowAggregatedInputPower,
optIfOMSnSrcCurrentHighAggregatedInputPower,
optIfOMSnSrcIntervalSuspectedFlag,
optIfOMSnSrcIntervalLastOutputPower,
optIfOMSnSrcIntervalLowOutputPower,
optIfOMSnSrcIntervalHighOutputPower,
optIfOMSnSrcIntervalLastAggregatedInputPower,
optIfOMSnSrcIntervalLowAggregatedInputPower,
optIfOMSnSrcIntervalHighAggregatedInputPower,
optIfOMSnSrcCurDaySuspectedFlag,
optIfOMSnSrcCurDayLowOutputPower,
optIfOMSnSrcCurDayHighOutputPower,
optIfOMSnSrcCurDayLowAggregatedInputPower,
optIfOMSnSrcCurDayHighAggregatedInputPower,
optIfOMSnSrcPrevDaySuspectedFlag,
optIfOMSnSrcPrevDayLastOutputPower,
optIfOMSnSrcPrevDayLowOutputPower,
optIfOMSnSrcPrevDayHighOutputPower,
optIfOMSnSrcPrevDayLastAggregatedInputPower,
optIfOMSnSrcPrevDayLowAggregatedInputPower,
optIfOMSnSrcPrevDayHighAggregatedInputPower
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
objects applicable to OMSn interfaces that
support source functions."::={ optIfGroups 17}optIfOMSnSourcePreOtnPMThresholdGroup OBJECT-GROUPOBJECTS{
optIfOMSnSrcCurrentLowerOutputPowerThreshold,
optIfOMSnSrcCurrentUpperOutputPowerThreshold,
optIfOMSnSrcCurrentLowerInputPowerThreshold,
optIfOMSnSrcCurrentUpperInputPowerThreshold
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
threshold objects applicable to OMSn interfaces that
that support source functions."::={ optIfGroups 18}
optIfOChGroupCommonGroup OBJECT-GROUPOBJECTS{
optIfOChGroupDirectionality
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all OChGroup interfaces."::={ optIfGroups 19}optIfOChGroupSinkPreOtnPMGroup OBJECT-GROUPOBJECTS{
optIfOChGroupSinkCurrentSuspectedFlag,
optIfOChGroupSinkCurrentAggregatedInputPower,
optIfOChGroupSinkCurrentLowAggregatedInputPower,
optIfOChGroupSinkCurrentHighAggregatedInputPower,
optIfOChGroupSinkCurrentOutputPower,
optIfOChGroupSinkCurrentLowOutputPower,
optIfOChGroupSinkCurrentHighOutputPower,
optIfOChGroupSinkIntervalSuspectedFlag,
optIfOChGroupSinkIntervalLastAggregatedInputPower,
optIfOChGroupSinkIntervalLowAggregatedInputPower,
optIfOChGroupSinkIntervalHighAggregatedInputPower,
optIfOChGroupSinkIntervalLastOutputPower,
optIfOChGroupSinkIntervalLowOutputPower,
optIfOChGroupSinkIntervalHighOutputPower,
optIfOChGroupSinkCurDaySuspectedFlag,
optIfOChGroupSinkCurDayLowAggregatedInputPower,
optIfOChGroupSinkCurDayHighAggregatedInputPower,
optIfOChGroupSinkCurDayLowOutputPower,
optIfOChGroupSinkCurDayHighOutputPower,
optIfOChGroupSinkPrevDaySuspectedFlag,
optIfOChGroupSinkPrevDayLastAggregatedInputPower,
optIfOChGroupSinkPrevDayLowAggregatedInputPower,
optIfOChGroupSinkPrevDayHighAggregatedInputPower,
optIfOChGroupSinkPrevDayLastOutputPower,
optIfOChGroupSinkPrevDayLowOutputPower,
optIfOChGroupSinkPrevDayHighOutputPower
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
objects applicable to OChGroup interfaces that
support sink functions."::={ optIfGroups 20}optIfOChGroupSinkPreOtnPMThresholdGroup OBJECT-GROUPOBJECTS{
optIfOChGroupSinkCurrentLowerInputPowerThreshold,
optIfOChGroupSinkCurrentUpperInputPowerThreshold,
optIfOChGroupSinkCurrentLowerOutputPowerThreshold,
optIfOChGroupSinkCurrentUpperOutputPowerThreshold
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
threshold objects applicable to OChGroup interfaces
that support sink functions."::={ optIfGroups 21}optIfOChGroupSourcePreOtnPMGroup OBJECT-GROUPOBJECTS{
optIfOChGroupSrcCurrentSuspectedFlag,
optIfOChGroupSrcCurrentOutputPower,
optIfOChGroupSrcCurrentLowOutputPower,
optIfOChGroupSrcCurrentHighOutputPower,
optIfOChGroupSrcCurrentAggregatedInputPower,
optIfOChGroupSrcCurrentLowAggregatedInputPower,
optIfOChGroupSrcCurrentHighAggregatedInputPower,
optIfOChGroupSrcIntervalSuspectedFlag,
optIfOChGroupSrcIntervalLastOutputPower,
optIfOChGroupSrcIntervalLowOutputPower,
optIfOChGroupSrcIntervalHighOutputPower,
optIfOChGroupSrcIntervalLastAggregatedInputPower,
optIfOChGroupSrcIntervalLowAggregatedInputPower,
optIfOChGroupSrcIntervalHighAggregatedInputPower,
optIfOChGroupSrcCurDaySuspectedFlag,
optIfOChGroupSrcCurDayLowOutputPower,
optIfOChGroupSrcCurDayHighOutputPower,
optIfOChGroupSrcCurDayLowAggregatedInputPower,
optIfOChGroupSrcCurDayHighAggregatedInputPower,
optIfOChGroupSrcPrevDaySuspectedFlag,
optIfOChGroupSrcPrevDayLastOutputPower,
optIfOChGroupSrcPrevDayLowOutputPower,
optIfOChGroupSrcPrevDayHighOutputPower,
optIfOChGroupSrcPrevDayLastAggregatedInputPower,
optIfOChGroupSrcPrevDayLowAggregatedInputPower,
optIfOChGroupSrcPrevDayHighAggregatedInputPower
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
objects applicable to OChGroup interfaces that
support source functions."::={ optIfGroups 22}optIfOChGroupSourcePreOtnPMThresholdGroup OBJECT-GROUPOBJECTS{
optIfOChGroupSrcCurrentLowerOutputPowerThreshold,
optIfOChGroupSrcCurrentUpperOutputPowerThreshold,
optIfOChGroupSrcCurrentLowerInputPowerThreshold,
optIfOChGroupSrcCurrentUpperInputPowerThreshold
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
threshold objects applicable to OChGroup interfaces that
that support source functions."::={ optIfGroups 23}optIfOChCommonGroup OBJECT-GROUPOBJECTS{
optIfOChDirectionality
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all OCh interfaces."::={ optIfGroups 24}optIfOChSinkGroupBasic OBJECT-GROUPOBJECTS{
optIfOChCurrentStatus
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all OCh interfaces that
support sink functions."::={ optIfGroups 25}optIfOChSinkPreOtnPMGroup OBJECT-GROUPOBJECTS{
optIfOChSinkCurrentSuspectedFlag,
optIfOChSinkCurrentInputPower,
optIfOChSinkCurrentLowInputPower,
optIfOChSinkCurrentHighInputPower,
optIfOChSinkIntervalSuspectedFlag,
optIfOChSinkIntervalLastInputPower,
optIfOChSinkIntervalLowInputPower,
optIfOChSinkIntervalHighInputPower,
optIfOChSinkCurDaySuspectedFlag,
optIfOChSinkCurDayLowInputPower,
optIfOChSinkCurDayHighInputPower,
optIfOChSinkPrevDaySuspectedFlag,
optIfOChSinkPrevDayLastInputPower,
optIfOChSinkPrevDayLowInputPower,
optIfOChSinkPrevDayHighInputPower
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
objects applicable to OCh interfaces that
support sink functions."::={ optIfGroups 26}optIfOChSinkPreOtnPMThresholdGroup OBJECT-GROUPOBJECTS{
optIfOChSinkCurrentLowerInputPowerThreshold,
optIfOChSinkCurrentUpperInputPowerThreshold
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
threshold objects applicable to OCh interfaces
that support sink functions."::={ optIfGroups 27}optIfOChSourcePreOtnPMGroup OBJECT-GROUPOBJECTS{
optIfOChSrcCurrentSuspectedFlag,
optIfOChSrcCurrentOutputPower,
optIfOChSrcCurrentLowOutputPower,
optIfOChSrcCurrentHighOutputPower,
optIfOChSrcIntervalSuspectedFlag,
optIfOChSrcIntervalLastOutputPower,
optIfOChSrcIntervalLowOutputPower,
optIfOChSrcIntervalHighOutputPower,
optIfOChSrcCurDaySuspectedFlag,
optIfOChSrcCurDayLowOutputPower,
optIfOChSrcCurDayHighOutputPower,
optIfOChSrcPrevDaySuspectedFlag,
optIfOChSrcPrevDayLastOutputPower,
optIfOChSrcPrevDayLowOutputPower,
optIfOChSrcPrevDayHighOutputPower
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
objects applicable to OCh interfaces that
support source functions."::={ optIfGroups 28}optIfOChSourcePreOtnPMThresholdGroup OBJECT-GROUPOBJECTS{
optIfOChSrcCurrentLowerOutputPowerThreshold,
optIfOChSrcCurrentUpperOutputPowerThreshold
}STATUScurrentDESCRIPTION"A collection of pre-OTN performance monitoring
threshold objects applicable to OCh interfaces
that support source functions."::={ optIfGroups 29}optIfOTUkCommonGroup OBJECT-GROUPOBJECTS{
optIfOTUkDirectionality,
optIfOTUkBitRateK
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all OTUk interfaces."::={ optIfGroups 30}optIfOTUkSourceGroup OBJECT-GROUPOBJECTS{
optIfOTUkTraceIdentifierTransmitted,
optIfOTUkSourceAdaptActive
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to OTUk interfaces that
support source functions."::={ optIfGroups 31}optIfOTUkSinkGroup OBJECT-GROUPOBJECTS{
optIfOTUkDAPIExpected,
optIfOTUkSAPIExpected,
optIfOTUkTraceIdentifierAccepted,
optIfOTUkTIMDetMode,
optIfOTUkTIMActEnabled,
optIfOTUkDEGThr,
optIfOTUkDEGM,
optIfOTUkSinkAdaptActive,
optIfOTUkSinkFECEnabled,
optIfOTUkCurrentStatus
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to OTUk interfaces that
support sink functions."::={ optIfGroups 32}optIfGCC0Group OBJECT-GROUPOBJECTS{
optIfGCC0Application,
optIfGCC0RowStatus
}STATUScurrentDESCRIPTION"A collection of GCC0 configuration objects."::={ optIfGroups 33}optIfODUkGroup OBJECT-GROUPOBJECTS{
optIfODUkDirectionality,
optIfODUkBitRateK,
optIfODUkTcmFieldsInUse,
optIfODUkPositionSeqCurrentSize,
optIfODUkPositionSeqPosition,
optIfODUkPositionSeqPointer,
optIfODUkTtpPresent
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all ODUk interfaces."::={ optIfGroups 34}optIfODUkTtpSourceGroup OBJECT-GROUPOBJECTS{
optIfODUkTtpTraceIdentifierTransmitted
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all interfaces that support
ODUk trail termination source functions."::={ optIfGroups 35}
optIfODUkTtpSinkGroup OBJECT-GROUPOBJECTS{
optIfODUkTtpDAPIExpected,
optIfODUkTtpSAPIExpected,
optIfODUkTtpTraceIdentifierAccepted,
optIfODUkTtpTIMDetMode,
optIfODUkTtpTIMActEnabled,
optIfODUkTtpDEGThr,
optIfODUkTtpDEGM,
optIfODUkTtpCurrentStatus
}STATUScurrentDESCRIPTION"A collection of ODUk configuration objects
applicable to all interfaces that support
ODUk trail termination sink functions."::={ optIfGroups 36}optIfODUkNimGroup OBJECT-GROUPOBJECTS{
optIfODUkNimDAPIExpected,
optIfODUkNimSAPIExpected,
optIfODUkNimTraceIdentifierAccepted,
optIfODUkNimTIMDetMode,
optIfODUkNimTIMActEnabled,
optIfODUkNimDEGThr,
optIfODUkNimDEGM,
optIfODUkNimCurrentStatus,
optIfODUkNimRowStatus
}STATUScurrentDESCRIPTION"A collection of ODUk Nim configuration objects."::={ optIfGroups 37}optIfGCC12Group OBJECT-GROUPOBJECTS{
optIfGCC12GCCPassThrough,
optIfGCC12Application,
optIfGCC12RowStatus
}STATUScurrentDESCRIPTION"A collection of GCC12 configuration objects."::={ optIfGroups 38}optIfODUkTCommonGroup OBJECT-GROUPOBJECTS{
optIfODUkTRowStatus
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all ODUkT instances."::={ optIfGroups 39}optIfODUkTSourceGroup OBJECT-GROUPOBJECTS{
optIfODUkTTraceIdentifierTransmitted,
optIfODUkTSourceLockSignalAdminState
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all ODUkT instances
that provide source functions."::={ optIfGroups 40}optIfODUkTSinkGroup OBJECT-GROUPOBJECTS{
optIfODUkTDAPIExpected,
optIfODUkTSAPIExpected,
optIfODUkTTraceIdentifierAccepted,
optIfODUkTTIMDetMode,
optIfODUkTTIMActEnabled,
optIfODUkTDEGThr,
optIfODUkTDEGM,
optIfODUkTCurrentStatus
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to all ODUkT instances
that provide sink functions."::={ optIfGroups 41}optIfODUkTSinkGroupCtp OBJECT-GROUPOBJECTS{
optIfODUkTSinkMode,
optIfODUkTSinkLockSignalAdminState
}STATUScurrentDESCRIPTION"A collection of configuration objects
applicable to ODUkT instances not
colocated with an ODUk TTP that
provide sink functions."::={ optIfGroups 42}optIfODUkTNimGroup OBJECT-GROUPOBJECTS{
optIfODUkTNimDAPIExpected,
optIfODUkTNimSAPIExpected,
optIfODUkTNimTraceIdentifierAccepted,
optIfODUkTNimTIMDetMode,
optIfODUkTNimTIMActEnabled,
optIfODUkTNimDEGThr,
optIfODUkTNimDEGM,
optIfODUkTNimCurrentStatus,
optIfODUkTNimRowStatus
}STATUScurrentDESCRIPTION"A collection of ODUkT Nim configuration objects."::={ optIfGroups 43}-- compliance specificationsoptIfOtnConfigCompl MODULE-COMPLIANCESTATUScurrentDESCRIPTION"Implementation requirements for the OTN configuration
functions defined in this MIB module."MODULE-- this moduleMANDATORY-GROUPS{
optIfOTMnGroup,
optIfOTSnCommonGroup
}GROUP optIfOTSnSourceGroupFull
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalTransport(196) for which the corresponding
instance of optIfOTSnDirectionality has the value
source(2) or bidirectional(3), the corresponding
instance of optIfOTMnReduced has the value false(2),
and the corresponding instance of optIfOTMnInterfaceType
specifies an OTMn interface type of 'IaDI'."GROUP optIfOTSnAPRStatusGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalTransport(196) that support Automatic Power
Reduction functions."GROUP optIfOTSnAPRControlGroup
DESCRIPTION"This group is optional, but is recommended for interfaces
of ifType opticalTransport(196) that provide Automatic
Power Reduction control functions."GROUP optIfOTSnSinkGroupBasic
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalTransport(196) for which the corresponding
instance of optIfOTSnDirectionality has the value
sink(1) or bidirectional(3)."GROUP optIfOTSnSinkGroupFull
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalTransport(196) for which the corresponding
instance of optIfOTSnDirectionality has the value
sink(1) or bidirectional(3), the corresponding
instance of optIfOTMnReduced has the value false(2),
and the corresponding instance of optIfOTMnInterfaceType
specifies an OTMn interface type of 'IaDI'."GROUP optIfOMSnCommonGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalTransport(196) that support access to the OMS
overhead information within the OTN Supervisory Channel."GROUP optIfOMSnSinkGroupBasic
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalTransport(196) that support access to the OMS Overhead
information within the OSC (OTN Supervisory Channel)
for which the corresponding
instance of optIfOMSnDirectionality has the value
sink(1) or bidirectional(3)."GROUP optIfOChGroupCommonGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannelGroup(219)."GROUP optIfOChCommonGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalTransport(195)."GROUP optIfOChSinkGroupBasic
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) for which the corresponding
instance of optIfOChDirectionality has the value
sink(1) or bidirectional(3)."GROUP optIfOTUkCommonGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OTUk layer functions."GROUP optIfOTUkSourceGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OTUk layer functions
and for which the corresponding instance of
optIfOTUkDirectionality has the value source(2) or
bidirectional(3)."GROUP optIfOTUkSinkGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OTUk layer functions
and for which the corresponding instance of
optIfOTUkDirectionality has the value sink(1) or
bidirectional(3)."GROUP optIfGCC0Group
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support GCC0 access functions.
It may be implemented only if the optIfOTUkCommonGroup
is also implemented."GROUP optIfODUkGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support ODUk layer functions."GROUP optIfODUkTtpSourceGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) for which the corresponding
instance of optIfODUkTtpPresent has the value
true(1) and for which the corresponding instance of
optIfODUkDirectionality has the value source(2) or
bidirectional(3). It may be implemented only if the
optIfODUkGroup is also implemented."GROUP optIfODUkTtpSinkGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) for which the corresponding
instance of optIfODUkTtpPresent has the value
true(1) and for which the corresponding instance of
optIfODUkDirectionality has the value sink(1) or
bidirectional(3). It may be implemented only if the
optIfODUkGroup is also implemented."GROUP optIfODUkNimGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) for which the corresponding
instance of optIfODUkTtpPresent has the value
false(2). It may be implemented only if the
optIfODUkGroup is also implemented."GROUP optIfGCC12Group
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support GCC12 access functions.
It may be implemented only if the optIfODUkGroup
is also implemented."GROUP optIfODUkTCommonGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support intrusive
tandem connection monitoring. It may be implemented
only if the optIfODUkGroup is also implemented."GROUP optIfODUkTSourceGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support intrusive
tandem connection monitoring and for which
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value false(2), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value true(1).
It may be implemented only if the optIfODUkGroup is
also implemented."GROUP optIfODUkTSinkGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support intrusive
tandem connection monitoring and for which
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It may be implemented only if the optIfODUkGroup is
also implemented."GROUP optIfODUkTSinkGroupCtp
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support intrusive
tandem connection monitoring and for which
optIfODUkTtpPresent is false(2) and
(i) optIfODUkDirectionality has the value bidirectional(3), or
(ii) optIfODUkDirectionality has the value sink(1) and
optIfODUkTCodirectional has the value true(1), or
(iii) optIfODUkDirectionality has the value source(3) and
optIfODUkTCodirectional has the value false(2).
It may be implemented only if the optIfODUkGroup and
optIfODUkTSinkGroup are also implemented."GROUP optIfODUkTNimGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support non-intrusive
tandem connection monitoring. It may be implemented
only if the optIfODUkGroup is also implemented."::={ optIfCompl 1}optIfPreOtnPMCompl MODULE-COMPLIANCESTATUScurrent
DESCRIPTION"Implementation requirements for Pre-OTN performance
monitoring functions defined in this MIB module."MODULE-- this moduleMANDATORY-GROUPS{
optIfPerfMonGroup
}GROUP optIfOTSnSinkPreOtnPMGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalTransport(196) that support OTSn sink
functions (i.e., for which the corresponding instance
of optIfOTSnDirectionality -- if implemented -- has
the value sink(1) or bidirectional(3))."GROUP optIfOTSnSinkPreOtnPMThresholdGroup
DESCRIPTION"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
optIfOTSnSinkPreOtnPMGroup is a prerequisite for
implementing this group."GROUP optIfOTSnSourcePreOtnPMGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalTransport(196) that support OTSn source
functions (i.e., for which the corresponding instance
of optIfOTSnDirectionality -- if implemented -- has
the value source(2) or bidirectional(3))."GROUP optIfOTSnSourcePreOtnPMThresholdGroup
DESCRIPTION"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
optIfOTSnSourcePreOtnPMGroup is a prerequisite for
implementing this group "GROUP optIfOMSnSinkPreOtnPMGroup
DESCRIPTION"This group is optional. It may be implemented by systems
with the necessary instrumentation on interfaces of ifType
opticalTransport(196) that support OMSn sink functions
(i.e., for which the corresponding instance of
optIfOMSnDirectionality -- if implemented -- has the value
sink(1) or bidirectional(3))."GROUP optIfOMSnSinkPreOtnPMThresholdGroup
DESCRIPTION"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
optIfOMSnSinkPreOtnPMGroup is a prerequisite for
implementing this group "GROUP optIfOMSnSourcePreOtnPMGroup
DESCRIPTION"This group is optional. It may be implemented by systems
with the necessary instrumentation on interfaces of ifType
opticalTransport(196) that support OMSn source functions
(i.e., for which the corresponding instance of
optIfOMSnDirectionality -- if implemented -- has the value
source(2) or bidirectional(3))."GROUP optIfOMSnSourcePreOtnPMThresholdGroup
DESCRIPTION"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
optIfOMSnSourcePreOtnPMGroup is a prerequisite for
implementing this group "GROUP optIfOChGroupSinkPreOtnPMGroup
DESCRIPTION"This group is optional. It may be implemented by systems
with the necessary instrumentation on interfaces of ifType
opticalChannelGroup(219) that support OChGroup sink functions
(i.e., for which the corresponding instance of
optIfOChGroupDirectionality -- if implemented -- has the value
sink(1) or bidirectional(3))."GROUP optIfOChGroupSinkPreOtnPMThresholdGroup
DESCRIPTION"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
optIfOChGroupSinkPreOtnPMGroup is a prerequisite for
implementing this group "GROUP optIfOChGroupSourcePreOtnPMGroup
DESCRIPTION"This group is optional. It may be implemented by systems
with the necessary instrumentation on interfaces of ifType
opticalChannelGroup(219) that support OChGroup source functions
(i.e., for which the corresponding instance of
optIfOChGroupDirectionality -- if implemented -- has the value
source(2) or bidirectional(3))."GROUP optIfOChGroupSourcePreOtnPMThresholdGroup
DESCRIPTION"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
optIfOChGroupSourcePreOtnPMGroup is a prerequisite for
implementing this group "GROUP optIfOChSinkPreOtnPMGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OCh sink functions
(i.e., for which the corresponding instance of
optIfOChDirectionality -- if implemented -- has the
value sink(1) or bidirectional(3))."GROUP optIfOChSinkPreOtnPMThresholdGroup
DESCRIPTION"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
optIfOChSinkPreOtnPMGroup is a prerequisite for
implementing this group "GROUP optIfOChSourcePreOtnPMGroup
DESCRIPTION"This group is mandatory for interfaces of ifType
opticalChannel(195) that support OCh source functions
(i.e., for which the corresponding instance of
optIfOChDirectionality -- if implemented -- has the
value source(2) or bidirectional(3))."GROUP optIfOChSourcePreOtnPMThresholdGroup
DESCRIPTION"This group is mandatory if and only if TCA notifications
are implemented. If the objects of this group are instantiated
then the implementation must also provide, in an
enterprise MIB, suitable TCA notification definitions and
notification control objects. Implementation of the
optIfOChSourcePreOtnPMGroup is a prerequisite for
implementing this group "::={ optIfCompl 2}END